System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
ID ID | Show |
|---|
|
ID ID | Hide |
|---|
For Housing ID For Housing ID |
|---|
|
Shaft Mount Type Shaft Mount Type |
|---|
|
Plain Bearing Type Plain Bearing Type |
|---|
 | Sleeve |
Static Thrust Load Capacity Static Thrust Load Capacity |
|---|
|
Material Material |
|---|
|
For Shaft Type For Shaft Type |
|---|
 | Round |
Lubrication Lubrication |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
|---|
|
For Shaft Surface Smoothness (Ra) For Shaft SurfaceSmoothness (Ra) |
|---|
|
Maximum Speed Maximum Speed |
|---|
|
About Plain Bearings
More
About Ball and Roller Bearings
More
High-Load Oil-Embedded Sleeve Bearings
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes them to release a thin layer of oil on the bearing’s surface. Color is silver because of the iron. These bearings are also magnetic due to the high iron content.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 2 1/2" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 3" | 4" | 17,800 lbs. @ 30 rpm | Lubricated | SAE 90 Oil | -15° to 300° | 00000000 | 000000 |
Needle-Roller Thrust Bearings
Thinner rollers allow these bearings to fit in tighter spaces than tapered-roller thrust bearings. Because of the large contact area between the rollers and washers (not included), these bearings are great for medium to heavy duty, low-friction jobs. For use on hardened and ground surfaces.
Washers allow you to use the bearing on unhardened and unground surfaces.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microns | Temp. Range, °F | Each | |
Steel Rollers | ||||||||||
Open | ||||||||||
| 2 1/2" | 3 1/4" | 5/64" | 6,200 | 37,500 | 3,300 | Required | 0.2 | 0° to 240° | 0000000 | 000000 |
| For Shaft Dia. | OD | Thick. | Washer Material | Each | |
| 2 1/2" | 3 1/4" | 0.032" | Steel | 00000000 | 00000 |
Washers for Needle-Roller Thrust Bearings
Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | OD | Thick. | Washer Material | Each | |
| 2 1/2" | 3 1/4" | 0.032" | Steel | 00000000 | 00000 |