Use these bearings in applications with frequent starts and stops because they operate with very little friction.

PTFE bearings have good chemical resistance.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads. They’re sometimes called 932 bronze bearings.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.

Open bearings dissipate heat more efficiently than sealed bearings.

Sealed bearings block out dust better than open bearings, but retain more heat.

For technical drawings and 3-D models, click on a part number.

These nylon bearings swivel inside their housing to compensate for over 20° of shaft misalignment. They are 80% lighter than steel bearings and resist corrosion, wear, shock, and vibration.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

A double row of precision ball bearings allows high speeds and smooth operation. Seals keep lubricant in and dirt out.

Carbon steel rod ends meet DIN dimensional and material standards.

For technical drawings and 3-D models, click on a part number.

For maximum mounting flexibility, cut the fully threaded shaft to whatever length you need. Also known as swing bolts and eyebolts, rod end bolts have no moving parts. They're designed to make pivoting or hinge movements in applications that don't need to compensate for misalignment.

For technical drawings and 3-D models, click on a part number.

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.

All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. They also have internal chamfers, so it's easier to insert bits, pins, and punches into the bushing. Some bushings have internal chamfers on both ends, so no matter which end of the bushing is inserted into your jig, your bits, pins, and other tooling enter easily. Having an internal chamfer on the bottom of your bushing may cause shavings to get caught and bind as you remove the bit, however.

DIN 179 bushings meet dimensional and material standards that make sure they're compatible with other parts and tools. Although DIN 179 is no longer an active standard, it's still a common reference point for designers.

Don't see the size you need? Additional sizes are available.

For technical drawings and 3-D models, click on a part number.

Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit. Drill bushings ensure accurate, consistent cuts and drilled holes from one part to the next. They sometimes also work as spacers, shims, and machinery bushings. Made of hardened, ground steel, these bushings hold their shape and resist wear over time. The flanged head protects your jig plate from damage caused by heavy use.

Although it's no longer an active standard, DIN 172 is still a common reference point for making sure parts are compatible with other parts and tools.

These bushings work in both countersunk and standard drill holes. To install, place the bushing inside the hole in your jig. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once centered, press the bushing into the hole with a hydraulic or lever press.

For technical drawings and 3-D models, click on a part number.

Precisely align, level, and adjust spacing on fasteners, shafts, and machinery with these shims.

For accurate leveling, choose materials such as steel or stainless steel, which are hard enough to resist scratching and deforming. Softer shims, like copper or aluminum, can be used as wear plates between components that rub together, preventing damage to equipment.

Stainless steel shims are more corrosion resistant than steel shims.Carbon steel shims have excellent strength and can be welded, but aren't as corrosion resistant as other shims.