Clear All
Component Component |
|---|
 | End Support |
System of Measurement System of Measurement |
|---|
|
ID ID | Show |
|---|
|
ID ID | Hide |
|---|
Locknut Thread Size Locknut Thread Size |
|---|
|
For Load Direction For Load Direction |
|---|
 | Radial |
 | Combined Radial and Thrust |
Dynamic Combined Load Capacity Dynamic CombinedLoad Capacity |
|---|
|
Material Material |
|---|
|
Number of Mounting Holes Number of Mounting Holes |
|---|
|
Bearing Trade Number Bearing Trade Number |
|---|
Width Width |
|---|
|
Static Combined Load Capacity Static CombinedLoad Capacity |
|---|
|
Face Mounting Hole Diameter Face Mounting Hole Diameter |
|---|
|
Face Mounting Hole Center-to-Center Height Face Mounting HoleCenter-to-Center Height |
|---|
|
Face Mounting Hole Center-to-Center Width Face Mounting HoleCenter-to-Center Width |
|---|
|
Height Height |
|---|
|
Top Mounting Hole Center-to-Center Width Top Mounting HoleCenter-to-Center Width |
|---|
|
Top Mounting Hole Diameter Top Mounting Hole Diameter |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
|---|
|
Selecting Compatible Lead Screws and Nuts
More
End Supports for Lead Screws and Ball Screws
A set of ball bearings reduces friction and secures the end of a ball or lead screw. Note: The end of your ball or lead screw must be machined before installing it into an end support.
For Radial Loads
End supports for radial loads handle loads perpendicular to the lead screw.
Face Mounting Holes | Top Mounting Holes | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ID | Ht. | Center Ht. | Wd. | Dp. | No. of Mounting Holes | Dia. | Ctr.-to-Ctr. Wd. | Ctr.-to-Ctr. Ht. | Dia. | Ctr.-to-Ctr. Wd. | Temperature Range, °F | Each | |
Alloy Steel | |||||||||||||
| 23/64" | 2" | 1" | 2 3/4" | 3/4" | 6 | 9/32" | 2" | 1 3/8" | 9/32" | 2" | -40° to 210° | 000000000 | 0000000 |
For Combined Radial and Thrust Loads
End supports for combined radial and thrust loads handle radial loads (perpendicular to the lead screw) and thrust loads (parallel to the lead screw).
Combined Load Cap., lbs. | Face Mounting Holes | Top Mounting Holes | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ID | Ht. | Center Ht. | Wd. | Dp. | Static | Dynamic | No. of Mounting Holes | Dia. | Ctr.-to-Ctr. Wd. | Ctr.-to-Ctr. Ht. | Dia. | Ctr.-to-Ctr. Wd. | Temperature Range, °F | Each | |
Alloy Steel | |||||||||||||||
| 23/64" | 2" | 1" | 2 3/4" | 1 51/64" | 1,000 | 440 | 6 | 9/32" | 2" | 1 3/8" | 9/32" | 2" | -40° to 210° | 00000000 | 0000000 |