System of Measurement System of Measurement |
---|
|
For Shaft Diameter For Shaft Diameter |
---|
|
ID ID | Show |
---|
|
ID ID | Hide |
---|
For Load Direction For Load Direction |
---|
![]() | Combined Radial and Thrust |
Dynamic Thrust Load Capacity Dynamic Thrust Load Capacity |
---|
|
Bearing Type Bearing Type |
---|
![]() | Roller |
Bearing Trade Number Bearing Trade Number |
---|

|
Static Radial Load Capacity Static Radial Load Capacity |
---|
|
Cage Material Cage Material |
---|
|
Inner Ring Width Inner Ring Width |
---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
---|
|
Static Thrust Load Capacity Static Thrust Load Capacity |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
Minimum Temperature Minimum Temperature |
---|
|
Maximum Temperature Maximum Temperature |
---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
Cage Width Cage Width |
---|
|
Construction Construction |
---|
|
For Shaft Type For Shaft Type |
---|
![]() | Round |
Ring Material Ring Material |
---|
|
Roller Material Roller Material |
---|
|
About Ball and Roller Bearings
More
About Plastic
More
Tapered-Roller Bearings


Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | Thrust Load Cap., lbs. | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | Bearing Trade Number | Dynamic | Static | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Each | |
Steel Ring | ||||||||||||
Open | ||||||||||||
3 1/4" | 5 1/4" | 1.031" | 47686/47620 | 9,750 | 58,750 | 6,750 | 69,250 | 1,400 | Required | -60° to 200° | 0000000 | 0000000 |
Slippery UHMW Polyethylene Tubes

These impact- and wear-resistant tubes offer 360° protection from scrapes and strikes to wires, cords, and anything that can slide through them. UHMW has a low-friction surface that resists sticking and binding.
Tight-tolerance tubes, also known as bushing stock, slide over rods and inside shafts to increase or decrease the diameter. Their precise sizing allows ascending sizes to fit inside each other to create a thicker wall.
For technical drawings and 3-D models, click on a part number.
- Color: White
- Temperature Range: -20° to 180° F
- Tensile Strength: 4,350-5,800 psi (Poor)
- Impact Strength: 16.8 ft.-lbs./in. (Excellent)
- Hardness: Durometer 65D-67D (Medium)
- For Use Outdoors: No
- Specifications Met: ASTM D4020
6" Lg. | |||||
---|---|---|---|---|---|
OD | OD Tolerance | ID | ID Tolerance | Each | |
1/4" Wall Thick. (-0.06" to 0") | |||||
3 3/4" | -0.030" to 0.000" | 3 1/4" | 0.000" to 0.030" | 0000000 | 000000 |
Clear Scratch- and UV-Resistant Acrylic Tubes
- Color: Clear
- Temperature Range: -40° to 180° F
- Tensile Strength; 9,195-11,030 (Good)
- Impact Strength: 0.040 ft.-lbs./in.
- Hardness: Rockwell M89-M96 (Hard)
- For Use Outdoors: Yes
- Specifications Met: UL 94 HB
When compared to cast acrylic tubes, these extruded acrylic tubes offer nearly the same performance at a fraction of the cost. Use them for sight gauges and protective covers. This scratch- and UV-resistant material stands up to outdoor use better than polycarbonate and maintains clarity over time.
For technical drawings and 3-D models, click on a part number.

OD | OD Tolerance | ID | ID Tolerance | Lg., ft. | Each | |
1/8" Wall Thick. | ||||||
---|---|---|---|---|---|---|
3 1/2" | -0.025" to 0.025" | 3 1/4" | -0.025" to 0.025" | 6 | 0000000 | 000000 |