System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
For Housing ID For Housing ID |
|---|
|
ID ID | Show |
|---|
|
ID ID | Hide |
|---|
For Load Direction For Load Direction |
|---|
 | Radial |
Mounted Bearing Type Mounted Bearing Type |
|---|
 | Base Mount |
Cage Material Cage Material |
|---|
|
Seal Type Seal Type |
|---|
|
For Shaft Type For Shaft Type |
|---|
 | Round |
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Lubrication Lubrication |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity |
|---|
|
Construction Construction |
|---|
|
For Shaft Surface Smoothness (Ra) For Shaft SurfaceSmoothness (Ra) |
|---|
|
Roller Bearing Type Roller Bearing Type |
|---|
|
Roller Material Roller Material |
|---|
|
About Plain Bearings
More
About Ball and Roller Bearings
More
Panel-Mount Oil-Embedded Sleeve Bearings
Unlike other sleeve bearings, these do not need to be fully inserted into a housing. Their unique shape creates a permanent, secure hold in thin panels. Bearings swivel to accommodate up to 5° of shaft misalignment. On startup, friction causes the bronze to release a thin layer of oil on the bearing’s surface. Not for use with plastic panels.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| Lg. | Spline OD | For Min. Sheet Metal Thick. | Dynamic Radial Load Capacity | Misalignment Capability | Lubrication | Lubricant | Temperature Range, °F | Each | |
Metric 840 Bronze Bearings | |||||||||
|---|---|---|---|---|---|---|---|---|---|
For 30mm Shaft Dia. | |||||||||
| 24mm | 48mm | 3.2mm | 2,200 lbs. @ 30 rpm | 5° | Lubricated | SAE 45 Oil | -20° to 200° | 0000000 | 000000 |
Precision Needle-Roller Bearings
Install these bearings directly onto hardened and ground shafts. They have higher load capacity, speed, and accuracy than standard needle-roller bearings.
Open bearings dissipate heat more efficiently than sealed bearings.
Shaft liners allow you to use the bearing on unhardened and unground shafts.
For technical drawings and 3-D models, click on a part number.
Oil-Embedded Mounted Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are self-aligning to compensate for shaft misalignment.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Bearing Wd. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic Radial Load Cap. | Temp. Range, °F | Alignment Style | Lubrication | Each | |
SAE 840 Bronze Bearings with Aluminum Housing | |||||||||||||
| 30mm | 32mm | 65mm | 127mm | 24mm | 24mm | 14mm | 101.5mm | 2,085 lbs. @ 60 rpm | -20° to 200° | Self Aligning | Lubricated | 0000000 | 000000 |