					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia.	For Housing ID	Wd.	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
6907	35mm	55mm	10mm	Steel	2,450	1,750	12,000	Lubricated	-20° to 230°	ABEC-1	00000000	000000

Shielded

					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia.	For Housing ID	Wd.	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
6006-2Z	30mm	55mm	13mm	Steel	3,100	1,850	14,000	Lubricated	-20° to 230°	ABEC-3	0000000	000000
6907-2Z	35mm	55mm	10mm	Steel	2,450	1,750	12,000	Lubricated	-20° to 230°	ABEC-1	00000000	00000

Sealed

					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia.	For Housing ID	Wd.	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
6006-2RS	30mm	55mm	13mm	Steel	3,100	1,850	8,000	Lubricated	-20° to 210°	ABEC-3	0000000	000000
6907-2RS	35mm	55mm	10mm	Steel	2,450	1,750	12,000	Lubricated	-20° to 230°	ABEC-1	00000000	00000

Sealed with Retaining Ring

Bearing with
Retaining
Ring

				Retaining Ring, mm			Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia.	For Housing ID	Wd.	OD	Thick.	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
6006-2RS	30mm	55mm	13mm	60.7	1.12	Steel	3,100	1,850	8,000	Lubricated	-40° to 210°	ABEC-1	0000000	000000

Permanently Lubricated Ball Bearings

A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication. Because it's solid, the lubricant blocks out water and dust, extending the life of the bearing.

Sealed bearings have even better resistance to dust and contaminants than open bearings.

For technical drawings and 3-D models, click on a part number.

					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia.	For Housing ID	Wd.	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
Open
6907	35mm	55mm	10mm	Steel	2,450	1,700	6,600	Lubricated	10° to 200°	ABEC-1	00000000	000000
Sealed
6006-2RS	30mm	55mm	13mm	Steel	2,250	1,600	7,000	Lubricated	10° to 200°	ABEC-1	00000000	00000
6907-2RS	35mm	55mm	10mm	Steel	10,900	1,700	6,600	Lubricated	10° to 200°	ABEC-1	00000000	00000

Stainless Steel Ball Bearings

Bearings are 440C stainless steel for good corrosion resistance.

Open bearings dissipate heat more efficiently than shielded and sealed bearings.

Shielded bearings block out dust and other contaminants, but do not dissipate heat as efficiently as open bearings.

For technical drawings and 3-D models, click on a part number.

Open

					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia.	For Housing ID	Wd.	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
6006H	30mm	55mm	13mm	440C Stainless Steel	2,500	1,450	15,000	Lubricated	-40° to 240°	ABEC-1	00000000	000000

Shielded

					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia.	For Housing ID	Wd.	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
6006ZZ	30mm	55mm	13mm	440C Stainless Steel	2,500	1,450	13,000	Lubricated	-40° to 240°	ABEC-1	00000000	000000

Permanently Lubricated Stainless Steel Ball Bearings

A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication. The solid lubricant blocks out water and dust, extending the life of the bearing.

Sealed bearings have even better resistance to dust and contaminants than open bearings.

For technical drawings and 3-D models, click on a part number.

Metric Bearings

					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
Open
6006H	30	55	13	440C Stainless Steel	2,250	1,600	7,000	Lubricated	-10° to 200°	ABEC-1	00000000	000000
6907H	35	55	10	440C Stainless Steel	2,450	1,750	6,000	Lubricated	-10° to 200°	ABEC-1	00000000	00000
Sealed
6006H-2RS	30	55	13	440C Stainless Steel	2,250	1,600	7,000	Lubricated	-10° to 200°	ABEC-1	00000000	00000
6907H-2RS	35	55	10	440C Stainless Steel	2,450	1,750	6,000	Lubricated	-10° to 200°	ABEC-1	00000000	00000

Food Industry Permanently Lubricated Stainless Steel Ball Bearings

Good for applications with incidental food contact, these 440C stainless steel bearings have a food-grade, solid polymer lubricant between the balls and ring that eliminates the need for additional lubrication. The solid lubricant blocks out water and dust, extending the life of the bearing.

Sealed bearings have even better resistance to dust and contaminants than open bearings.

For technical drawings and 3-D models, click on a part number.

Metric Bearings

					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating	Specifications Met		Each
Sealed
6006H-2RS	30	55	13	440C Stainless Steel	2,518	1,488	7,000	Lubricated	-40° to 200°	ABEC-1	FDA Compliant 21 CFR 178.3570	00000000	000000
6907H-2RS	35	55	10	440C Stainless Steel	2,079	1,394	6,000	Lubricated	-40° to 200°	ABEC-1	FDA Compliant 21 CFR 178.3570	00000000	000000

Ultra-Corrosion-Resistant Stainless Steel Ball Bearings

These 316 stainless steel bearings are more corrosion resistant than our other stainless steel bearings, but they have a lower load capacity.

For technical drawings and 3-D models, click on a part number.

					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia.	For Housing ID	Wd.	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
Open
6006	30mm	55mm	13mm	316 Stainless Steel	270	180	720	Required	-40° to 140°	Not Rated	00000000	000000

Plastic Ball Bearings

These acetal bearings have good all-around corrosion and chemical resistance.

316 stainless steel balls have excellent corrosion resistance.

Glass balls have even more corrosion resistance than stainless steel balls.

For technical drawings and 3-D models, click on a part number.

					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia.	For Housing ID	Wd.	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
316 Stainless Steel Ball
Open
6006	30mm	55mm	13mm	Acetal Plastic	92	61	729	Not Required	-40° to 180°	Not Rated	00000000	000000
16006	30mm	55mm	9mm	Acetal Plastic	92	61	729	Not Required	-40° to 180°	Not Rated	00000000	00000
Glass Ball
Open
6006	30mm	55mm	13mm	Acetal Plastic	92	61	729	Not Required	-40° to 180°	Not Rated	00000000	00000
16006	30mm	55mm	9mm	Acetal Plastic	92	61	729	Not Required	-40° to 180°	Not Rated	00000000	00000

Angular-Contact Thrust Ball Bearings

Open

Install these bearings for use with combined radial and thrust loads. They are often used in spindle applications and can be combined with cylindrical roller bearings to better handle radial loads.

Single-row bearings handle thrust loads on one side. For applications with thrust loads on both sides, mount them in pairs.

Open bearings dissipate heat more efficiently than shielded and sealed bearings.

For technical drawings and 3-D models, click on a part number.

					Combined Load Cap., lbs.
Bearing Trade Number	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Contact Angle	Temp. Range, °F	ABEC Rating		Each
Single Row
Open
7006	30	55	13	Steel	3,200	1,750	32,000	Required	15°	-30° to 140°	ABEC-7	0000000	0000000

Ultra-Thin Ball Bearings

Open

Shielded

These bearings have twice as many contact points as angular-contact ball bearings. Fit onto large-diameter hollow shafts to run air and hydraulic lines, electrical wiring, and other components through moving parts in assemblies such as index and rotary tables, packaging equipment, and robotics.

440 stainless steel bearings are more corrosion resistant than steel bearings.

Open bearings dissipate heat more efficiently than shielded bearings.

Shielded bearings block out dust and other contaminants, but do not dissipate heat as efficiently as open bearings.

For technical drawings and 3-D models, click on a part number.

			Radial Load Cap., lbs.		Thrust Load Cap., lbs.		Moment Load Cap., ft.-lbs.
For Shaft Dia.	For Housing ID	Wd.	Dynamic	Static	Dynamic	Static	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
Steel Ring
Open
35mm	55mm	10mm	2,450	1,750	Not Rated	Not Rated	Not Rated	Not Rated	14,000	Lubricated	-50° to 130°	ABEC-1	00000000	000000
45mm	55mm	6mm	580	530	Not Rated	Not Rated	Not Rated	Not Rated	4,600	Lubricated	-50° to 130°	ABEC-1	00000000	000000
Shielded
35mm	55mm	10mm	2,450	1,750	Not Rated	Not Rated	Not Rated	Not Rated	12,000	Lubricated	-40° to 150°	ABEC-1	00000000	00000
440 Stainless Steel Ring
Open
35mm	55mm	10mm	2,450	1,750	Not Rated	Not Rated	Not Rated	Not Rated	14,000	Lubricated	-50° to 130°	ABEC-1	00000000	00000
Shielded
35mm	55mm	10mm	2,450	1,750	Not Rated	Not Rated	Not Rated	Not Rated	12,000	Lubricated	-40° to 150°	ABEC-1	00000000	00000

Oil-Embedded Sleeve Bearings

Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Metric 841 Bronze Bearings

For 45 mm Shaft Dia.
For Housing ID, mm	Lg., mm	Dynamic Radial Load Capacity	Lubrication	Lubricant	Temperature Range, °F		Each
55	35	4,800 lbs. @ 30 rpm	Lubricated	SAE 30 Oil	-35° to 300°	00000000	000000
55	45	6,250 lbs. @ 30 rpm	Lubricated	SAE 30 Oil	-35° to 300°	00000000	00000
55	55	7,650 lbs. @ 30 rpm	Lubricated	SAE 30 Oil	-35° to 300°	00000000	00000
55	60	8,200 lbs. @ 30 rpm	Lubricated	SAE 30 Oil	-35° to 300°	00000000	00000

High-Load Oil-Embedded Sleeve Bearings

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes them to release a thin layer of oil on the bearing’s surface. Color is silver because of the iron. These bearings are also magnetic due to the high iron content.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

863 Iron-Copper Bearings

For 45mm Shaft Dia.
For Housing ID	Lg.	Dynamic Radial Load Capacity	Lubrication	Lubricant	Temperature Range, °F		Each
55mm	45mm	7,850 lbs. @ 30 rpm	Lubricated	SAE 90 Oil	-15° to 300°	00000000	000000
55mm	55mm	9,600 lbs. @ 30 rpm	Lubricated	SAE 90 Oil	-15° to 300°	00000000	00000

Ultra-Low-Friction Oil-Embedded Sleeve Bearings

For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Metric 841 Bronze Bearings

For 45mm Shaft Dia.
For Housing ID, mm	Lg., mm	Dynamic Radial Load Capacity	Lubrication	Lubricant	Temperature Range, °F		Each
55	45	6,250 lbs. @ 30 rpm	Lubricated	SAE 20 Oil with PTFE	-60° to 300°	00000000	000000
55	55	7,650 lbs. @ 30 rpm	Lubricated	SAE 20 Oil with PTFE	-60° to 300°	00000000	00000

High-Load Ultra-Low-Friction Oil-Embedded Sleeve Bearings

Use these bearings for frequent starts and stops in high-load applications. Startup friction causes these bearings to release a thin layer of oil that contains PTFE to lubricate the bearing’s surface. All have more iron content than standard oil-embedded bearings to handle heavier loads and higher shock loads, but operate at lower speeds.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

863 Bearing Bronze
For Housing ID, mm	Length, mm	Dynamic Radial Load Capacity	Lubrication	Lubricant	Temperature Range, °F		Each
For 45 mm Shaft Dia.
55	45	7,850 lbs. @ 30 rpm	Lubricated	SAE 20 Oil with PTFE	-60° to 300°	00000000	000000
55	55	9,600 lbs. @ 30 rpm	Lubricated	SAE 20 Oil with PTFE	-60° to 300°	00000000	00000

Light Duty Dry-Running Sleeve Bearings

Use where high loads and speeds are not required.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Metric Nylon Bearings
For Housing ID	Lg.	Dynamic Radial Load Capacity	Color	Temperature Range, °F		Each
For 45mm Shaft Dia.
55mm	35mm	430 lbs. @ 30 rpm	Off-White	-10° to 220°	0000000	000000
55mm	45mm	560 lbs. @ 30 rpm	Off-White	-10° to 220°	00000000	00000
55mm	55mm	680 lbs. @ 30 rpm	Off-White	-10° to 220°	00000000	00000
55mm	60mm	750 lbs. @ 30 rpm	Off-White	-10° to 220°	00000000	00000

High-Temperature Dry-Running Sleeve Bearings

Graphite provides a layer of dry lubrication that operates in high-temperature environments.

954 aluminum-bronze bearings have high strength and excellent corrosion resistance, making them suitable for use in marine and mining applications.

Grooved bearings have a graphite-filled groove on the inside of the bearing that distributes lubricant evenly along the bearing’s surface.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Grooved

Metric 954 Aluminum-Bronze Bearings
For Housing ID	Lg.	Dynamic Radial Load Capacity	Lubrication Method	Temperature Range, °F		Each
For 50mm Shaft Dia.
55mm	50mm	15,100 lbs. @ 30 rpm	Grooved	-350° to 500°	00000000	000000
55mm	65mm	19,600 lbs. @ 30 rpm	Grooved	-350° to 500°	00000000	00000

Food Industry Dry-Running Sleeve Bearings

Made of FDA-listed materials or FDA compliant, these bearings are for use in food applications. They also withstand caustic and washdown environments.

Acetal bearings are FDA compliant for direct contact with food. They’re also bright blue, making them easy to spot if they fall into your line.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Metric Acetal Plastic Bearings
For Housing ID	Lg.	Dynamic Radial Load Capacity	Color	Temperature Range, °F	Specifications Met		Each
For 50mm Shaft Dia.
55mm	20mm	32 lbs. @ 30 rpm	Blue	-50° to 190°	FDA Compliant 21 CFR 177.1550	00000000	00000
55mm	30mm	32 lbs. @ 30 rpm	Blue	-50° to 190°	FDA Compliant 21 CFR 177.1550	00000000	0000
55mm	40mm	43 lbs. @ 30 rpm	Blue	-50° to 190°	FDA Compliant 21 CFR 177.1550	00000000	0000
55mm	60mm	50 lbs. @ 30 rpm	Blue	-50° to 190°	FDA Compliant 21 CFR 177.1550	00000000	0000

Chemical-Resistant Dry-Running Sleeve Bearings

Fiberglass-Backed PTFE Plastic

These bearings stand up to a wider range of chemicals than other dry-running sleeve bearings.

Fiberglass-backed PTFE are strong and vibration resistant. A layer of PTFE on the ID of the bearing reduces friction.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

Metric Fiberglass-Backed PTFE Plastic Bearings
For Housing ID	Lg.	Dynamic Radial Load Cap.	Color	Temp. Range, °F		Each
For 45mm Shaft Dia.
55mm	30mm	13,500 lbs. @ 10 rpm	Gray	-145° to 320°	00000000	000000
55mm	40mm	18,000 lbs. @ 10 rpm	Gray	-145° to 320°	00000000	00000
55mm	60mm	27,050 lbs. @ 10 rpm	Gray	-145° to 320°	00000000	00000

Multipurpose Sleeve Bearings

These 660 leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads. They’re sometimes called 932 bronze bearings.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Metric 660 Leaded Bronze Bearings
For Housing ID	Lg.	Dynamic Radial Load Capacity	Lubrication	Temperature Range, °F		Each
For 40mm Shaft Dia.
55mm	75mm	18,600 lbs. @ 30 rpm	Required	-350° to 450°	00000000	000000
For 45mm Shaft Dia.
55mm	45mm	12,550 lbs. @ 30 rpm	Required	-350° to 450°	00000000	00000
For 50mm Shaft Dia.
55mm	50mm	15,500 lbs. @ 30 rpm	Required	-350° to 450°	00000000	00000
55mm	65mm	20,150 lbs. @ 30 rpm	Required	-350° to 450°	00000000	00000
55mm	100mm	31,000 lbs. @ 30 rpm	Required	-350° to 450°	00000000	00000

Multipurpose Sleeve Bearings with Groove

A figure-8-shaped groove provides a flow path for lubricant, distributing it evenly along the bearing’s surface. Bearings are cast bronze, making them strong, wear resistant, and excellent at handling shock loads. 660 leaded bronze is sometimes called 932 bronze.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Metric 660 Leaded Bronze Bearings
For Housing ID	Lg.	Dynamic Radial Load Capacity	Lubrication	Temperature Range, °F		Each
For 40mm Shaft Dia.
55mm	75mm	21,000 lbs. @ 30 rpm	Required	-350° to 450°	00000000	000000
For 45mm Shaft Dia.
55mm	45mm	12,600 lbs. @ 30 rpm	Required	-350° to 450°	00000000	00000
For 50mm Shaft Dia.
55mm	50mm	14,000 lbs. @ 30 rpm	Required	-350° to 450°	00000000	00000
55mm	65mm	18,200 lbs. @ 30 rpm	Required	-350° to 450°	00000000	00000

Light Duty Dry-Running Flanged Sleeve Bearings

Use where high loads and speeds are not required.

Thermoplastic-blend bearings have low moisture absorption and create very low friction in applications with light loads, and frequent starts and stops.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Thermoplastic-Blend Bearings
For Housing ID	Lg.	Flange OD	Flange Thick.	Dynamic Radial Load Capacity	Dynamic Thrust Load Capacity	Color	Temperature Range, °F		Each
For 50mm Shaft Dia.
55mm	11.5mm	63mm	2mm	550 lbs. @ 30 rpm	890 lbs. @ 30 rpm	Yellow	-50° to 190°	00000000	000000
55mm	50mm	63mm	2mm	2,400 lbs. @ 30 rpm	890 lbs. @ 30 rpm	Yellow	-50° to 190°	00000000	00000

Corrosion-Resistant Flanged Sleeve Bearings

The addition of iron and aluminum gives these bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

954 Aluminum-Bronze Bearings
For Housing ID	Lg.	Flange OD	Flange Thick.	Dynamic Radial Load Capacity	Dynamic Thrust Load Capacity	Lubrication	Temperature Range, °F		Each
For 45mm Shaft Dia.
55mm	65mm	65mm	5mm	20,400 lbs. @ 30 rpm	12,050 lbs. @ 30 rpm	Required	-350° to 500°	00000000	000000

Tapered-Roller Bearings

Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.

For technical drawings and 3-D models, click on a part number.

				Radial Load Cap., lbs.		Thrust Load Cap., lbs.
For Shaft Dia.	For Housing ID	Wd.	Bearing Trade Number	Dynamic	Static	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F		Each
Steel Ring
Open
30mm	55mm	13mm	32006X	2,100	10,200	1,550	12,800	3,500	Required	-60° to 200°	0000000	000000
30mm	55mm	13mm	32006XA	8,500	10,950	6,250	Not Rated	6,700	Required	-50° to 300°	0000000	00000