About Plain Bearings
More
Ultra-Low-Friction Dry-Running Thrust Bearings
Use these bearings in applications with frequent starts and stops because they operate with very little friction.
PTFE bearings have good chemical resistance.
Rulon J bearings create the least amount of friction of any bearing that we offer. They handle heavier loads than PTFE bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
Food Industry Dry-Running Thrust Bearings
Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.
Rulon 641 bearings are stronger than UHMW bearings and withstand a wider range of temperatures.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD, mm | Thick., mm | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Specifications Met | Each | |
For 6 mm Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 11.8 | 1.5 | 80 lbs. @ 120 rpm | White | -400° to 550° | FDA Compliant 21 CFR 177.1550, USP Class VI | 0000000 | 000000 |
| 12.8 | 0.8 | 95 lbs. @ 120 rpm | White | -400° to 550° | FDA Compliant 21 CFR 177.1550, USP Class VI | 0000000 | 00000 |
Water-Resistant Dry-Running Thrust Bearings
Good for underwater applications, these bearings won’t swell or warp when wet.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD, mm | Thick., mm | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
Metric Rulon LR Plastic Bearings | ||||||
|---|---|---|---|---|---|---|
For 6 mm Shaft Dia. | ||||||
| 12.8 | 0.8 | 95 lbs. @ 120 rpm | Maroon | -400° to 550° | 0000000 | 00000 |
Metric Press-Fit Drill Bushings
Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.
All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. They also have internal chamfers, so it's easier to insert bits, pins, and punches into the bushing. Some bushings have internal chamfers on both ends, so no matter which end of the bushing is inserted into your jig, your bits, pins, and other tooling enter easily. Having an internal chamfer on the bottom of your bushing may cause shavings to get caught and bind as you remove the bit, however.
DIN 179 bushings meet dimensional and material standards that make sure they're compatible with other parts and tools. Although DIN 179 is no longer an active standard, it's still a common reference point for designers.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Tolerance | Each | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD, mm | Lg., mm | Internal Chamfer | For Drill Bit Size | ID, mm | OD, mm | Lg., mm | Drill Bushing Type | Material | Hardness | Specifications Met | 1-5 | 6-11 | 12-Up | |
6.2 mm ID | ||||||||||||||
| 12 | 10 | Both Ends | 6.2 mm | 0.013 to 0.028 | 0.012 to 0.023 | -0.2 to 0.2 | PM | Steel | Rockwell C61 | __ | 000000000 | 000000 | 00000 | 00000 |
| 12 | 16 | One End | 6.2 mm | 0.013 to 0.028 | 0.012 to 0.023 | -0.2 to 0.2 | PM | Steel | Rockwell C61 | DIN 179 | 000000000 | 00000 | 0000 | 0000 |
Metric Press-Fit Drill Bushings with Head
Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit. Drill bushings ensure accurate, consistent cuts and drilled holes from one part to the next. They sometimes also work as spacers, shims, and machinery bushings. Made of hardened, ground steel, these bushings hold their shape and resist wear over time. The flanged head protects your jig plate from damage caused by heavy use.
Although it's no longer an active standard, DIN 172 is still a common reference point for making sure parts are compatible with other parts and tools.
These bushings work in both countersunk and standard drill holes. To install, place the bushing inside the hole in your jig. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once centered, press the bushing into the hole with a hydraulic or lever press.
For technical drawings and 3-D models, click on a part number.
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD, mm | Lg., mm | OD, mm | Thick., mm | ID, mm | OD, mm | Lg., mm | Drill Bushing Type | Material | Hardness | Specifications Met | 1-5 | 6-11 | 12-Up | |
6.2 mm ID | ||||||||||||||
| 12 | 7 | 15 | 3 | 0.013 to 0.028 | 0.012 to 0.023 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 000000 | 000000 | 00000 |
| 12 | 13 | 15 | 3 | 0.013 to 0.028 | 0.012 to 0.023 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
| 12 | 17 | 15 | 3 | 0.013 to 0.028 | 0.012 to 0.023 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |