System of Measurement System of Measurement |
|---|
|
For Load Direction For Load Direction |
|---|
 | Combined Radial and Thrust |
 | Thrust |
OD OD | Show |
|---|
|
OD OD | Hide |
|---|
Inner Ring Width Inner Ring Width |
|---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
|---|
|
Construction Construction |
|---|
|
Dynamic Thrust Load Capacity Dynamic Thrust Load Capacity |
|---|
|
|
Static Radial Load Capacity Static Radial Load Capacity |
|---|
|
Cage Material Cage Material |
|---|
|
For Housing ID For Housing ID |
|---|
|
Bearing Trade Number Bearing Trade Number |
|---|
|
Lubrication Lubrication |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
About Plain Bearings
More
About Ball and Roller Bearings
More
Thrust Ball Bearings for Shaft Ends
Use these bearings as miniature high-precision turntables. They have a unique design that allows your shaft to sit on top of the bearing rather than being inserted through it. Bearings can be bonded to a mounting plate or press-fit into a hole.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Each | |
Open | ||||||||||
| 1 11/16" | 1 11/16" | 1 1/4" | Steel | 7,550 | 14,100 | 1,500 | Required | -40° to 250° | 0000000 | 000000 |
Oil-Embedded Thrust Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD | Thick. | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 1 1/4" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 1 11/16" | 1/8" | 2,000 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
Multipurpose Thrust Bearings
These 660 leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads. They’re sometimes called 932 bronze bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD | Thick. | Dynamic Thrust Load Capacity | Lubrication | Temperature Range, °F | Each | |
660 Leaded Bronze | ||||||
|---|---|---|---|---|---|---|
For 1 1/4" Shaft Dia. | ||||||
| 1 11/16" | 1/8" | Not Rated | Required | -350° to 450° | 00000000 | 00000 |
Tapered-Roller Bearings
Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | Thrust Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | For Housing ID | Wd. | Bearing Trade Number | Dynamic | Static | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Each | |
Steel Ring | ||||||||||||
Open | ||||||||||||
| 5/8" | 1 11/16" | 3/8" | 11590/11520 | 1,000 | 3,900 | 1,200 | 8,000 | 5,000 | Required | -60° to 200° | 0000000 | 000000 |
Needle-Roller Thrust Bearings
Thinner rollers allow these bearings to fit in tighter spaces than tapered-roller thrust bearings. Because of the large contact area between the rollers and washers (not included), these bearings are great for medium to heavy duty, low-friction jobs. For use on hardened and ground surfaces.
Washers allow you to use the bearing on unhardened and unground surfaces.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microns | Temp. Range, °F | Each | |
Steel Rollers | ||||||||||
Open | ||||||||||
| 7/8" | 1 11/16" | 5/64" | 4,400 | 18,600 | 7,500 | Required | 0.2 | 0° to 240° | 0000000 | 00000 |
| For Shaft Dia. | OD | Thick. | Washer Material | Each | |
| 7/8" | 1 11/16" | 0.032" | Steel | 0000000 | 00000 |
Washers for Needle-Roller Thrust Bearings
Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | OD | Thick. | Washer Material | Each | |
| 7/8" | 1 11/16" | 0.032" | Steel | 0000000 | 00000 |
Self-Centering Screw-Clamp Bushings
A mounting flange prevents movement during tightening, so it's easy to center these bushings in your sprocket. They are also good for shock loads. When you tighten the included screws, the bushing's inner sleeve contracts onto the shaft and the outer sleeve expands to hold your sprocket, pulley, or gear. They can be mounted on shafts with or without keyways.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | OD | Overall Wd. | Max. Torque, in.-lbs. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
| 1" | 1 11/16" | 1 3/16" | 3,050 | 90 | Steel | Clamping Screws | 0000000 | 000000 |