115 mm OD Bearings | McMaster-Carr

					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia.	For Housing ID	Wd.	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating	Specifications Met		Each
6015-2Z	75mm	115mm	20mm	Steel	9,400	7,500	6,900	Lubricated	-20° to 230°	ABEC-1	DIN 625-1	00000000	0000000

Sealed

					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia.	For Housing ID	Wd.	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating	Specifications Met		Each
6015-2RS	75mm	115mm	20mm	Steel	9,400	7,500	3,000	Lubricated	-20° to 230°	ABEC-1	DIN 625-1	00000000	0000000

Permanently Lubricated Ball Bearings

A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication. Because it's solid, the lubricant blocks out water and dust, extending the life of the bearing.

Sealed bearings have even better resistance to dust and contaminants than open bearings.

For technical drawings and 3-D models, click on a part number.

					Radial Load Cap., lbs.
Bearing Trade Number	For Shaft Dia.	For Housing ID	Wd.	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
Sealed
6015-2RS	75mm	115mm	20mm	Steel	6,850	6,350	3,000	Lubricated	10° to 200°	ABEC-1	00000000	0000000

Ultra-Thin Ball Bearings

Open

Shielded

These bearings have twice as many contact points as angular-contact ball bearings. Fit onto large-diameter hollow shafts to run air and hydraulic lines, electrical wiring, and other components through moving parts in assemblies such as index and rotary tables, packaging equipment, and robotics.

Open bearings dissipate heat more efficiently than shielded bearings.

Shielded bearings block out dust and other contaminants, but do not dissipate heat as efficiently as open bearings.

For technical drawings and 3-D models, click on a part number.

			Radial Load Cap., lbs.		Thrust Load Cap., lbs.		Moment Load Cap., ft.-lbs.
For Shaft Dia.	For Housing ID	Wd.	Dynamic	Static	Dynamic	Static	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	ABEC Rating		Each
Steel Ring
Open
90mm	115mm	13mm	4,250	4,400	Not Rated	Not Rated	Not Rated	Not Rated	6,300	Lubricated	-50° to 130°	ABEC-1	00000000	0000000
Shielded
90mm	115mm	13mm	4,250	4,400	Not Rated	Not Rated	Not Rated	Not Rated	5,300	Lubricated	-40° to 150°	ABEC-1	00000000	000000

Precision Angular-Contact Thrust Ball Bearings

These bearings have angular raceways for combined thrust and radial loads—install them where precision tolerances are required for accuracy and high speeds. They’re often used in spindle applications. To handle thrust loads in both directions, they have a double-row construction. Pair them with cylindrical roller bearings to better handle radial loads. They have an open construction to dissipate heat efficiently.

For technical drawings and 3-D models, click on a part number.

					Combined Load Capacity, lbs.
Bearing Trade Number	For Shaft Diameter, mm	For Housing ID, mm	Width, mm	Ring Material	Dynamic	Static	Maximum Speed, rpm	Lubrication	Contact Angle	Temperature Range, °F	ABEC Rating		Each
Double Row
Open
BTW 75	75	115	48	Steel	8,900	26,050	6,300	Required	60°	-40° to 240°	ABEC-7	0000000	000000000

Bearing Retaining Jam Nuts

Used in pairs or with another bearing retaining nut, these jam nuts—often called shaft nuts—hold bearings, bushings, pulleys, and gears in place on your threaded shaft or spindle. Threading two nuts tightly against each other makes it harder for vibration to loosen your assembly than if you used only one nut. For the nut closer to the bearing, position the stepped face towards the bearing. These jam nuts have holes on the side, so you can tighten and loosen them with a pin spanner wrench. Made of carbon steel, they’re strong and wear resistant. All meet DIN 1816, an international standard for bearing locknut dimensions.

For technical drawings and 3-D models, click on a part number.

Thread
Size	Pitch, mm	Spacing	OD, mm	Wd., mm	Specifications Met		Each
Carbon Steel
Stepped Face
M80	2	Extra Fine	115	16	DIN 1816	0000000	000000

Metric Press-Fit Drill Bushings

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.

All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. They also have internal chamfers, so it's easier to insert bits, pins, and punches into the bushing. Don't see the size you need? Additional sizes are available.

For technical drawings and 3-D models, click on a part number.

				Tolerance							Each
OD, mm	Lg., mm	Internal Chamfer	For Drill Bit Size	ID, mm	OD, mm	Lg., mm	Drill Bushing Type	Material	Hardness		1-5	6-11	12-Up
85 mm ID
115	45	One End	85 mm	0.012 to 0.034	0.079 to 0.101	-0.35 to 0.35	PM	Steel	Rockwell C61	000000000	000000	000000	000000
115	89	One End	85 mm	0.012 to 0.034	0.079 to 0.101	-0.35 to 0.35	PM	Steel	Rockwell C61	000000000	000000	000000	000000
115	112	One End	85 mm	0.012 to 0.034	0.079 to 0.101	-0.35 to 0.35	PM	Steel	Rockwell C61	000000000	000000	000000	000000
90 mm ID
115	45	One End	90 mm	0.012 to 0.034	0.079 to 0.101	-0.35 to 0.35	PM	Steel	Rockwell C61	000000000	00000	00000	00000
115	89	One End	90 mm	0.012 to 0.034	0.079 to 0.101	-0.35 to 0.35	PM	Steel	Rockwell C61	000000000	000000	000000	000000
115	112	One End	90 mm	0.012 to 0.034	0.079 to 0.101	-0.35 to 0.35	PM	Steel	Rockwell C61	000000000	000000	000000	000000
95 mm ID
115	45	One End	95 mm	0.012 to 0.034	0.079 to 0.101	-0.35 to 0.35	PM	Steel	Rockwell C61	000000000	00000	00000	00000
115	89	One End	95 mm	0.012 to 0.034	0.079 to 0.101	-0.35 to 0.35	PM	Steel	Rockwell C61	000000000	000000	000000	000000
115	112	One End	95 mm	0.012 to 0.034	0.079 to 0.101	-0.35 to 0.35	PM	Steel	Rockwell C61	000000000	000000	000000	000000