System of Measurement System of Measurement |
|---|
|
OD OD | Show |
|---|
|
OD OD | Hide |
|---|
ID ID |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
For Load Direction For Load Direction |
|---|
 | Thrust |
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Thread Size Thread Size |
|---|
Cage Material Cage Material |
|---|
|
Dynamic Thrust Load Capacity Dynamic Thrust Load Capacity |
|---|
|
For Shaft Surface Smoothness (Ra) For Shaft SurfaceSmoothness (Ra) |
|---|
|
Lubrication Lubrication |
|---|
|
Maximum Speed Maximum Speed |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Roller Bearing Type Roller Bearing Type |
|---|
|
Roller Material Roller Material |
|---|
|
Static Thrust Load Capacity Static Thrust Load Capacity |
|---|
|
Seal Type Seal Type |
|---|
|
For Shaft Type For Shaft Type |
|---|
 | Round |
About Ball and Roller Bearings
More
About Shaft Collars
Shaft collars are useful for holding and positioning components on a shaft. They can also serve as mechanical stops and stroke limiters.
More
Needle-Roller Thrust Bearings
Thinner rollers allow these bearings to fit in tighter spaces than tapered-roller thrust bearings. Because of the large contact area between the rollers and washers (not included), these bearings are great for medium to heavy duty, low-friction jobs. For use on hardened and ground surfaces.
Washers allow you to use the bearing on unhardened and unground surfaces.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microns | Temp. Range, °F | Specifications Met | Each | |
Steel Rollers | |||||||||||
Open | |||||||||||
| 110mm | 145mm | 4mm | 21,800 | 139,300 | 2,230 | Required | 0.2 | 0° to 240° | DIN 5405-3, ISO 303 | 00000000 | 0000000 |
| For Shaft Dia. | OD | Thick. | Washer Material | Specifications Met | Each | |
| 110mm | 145mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 000000 |
Washers for Needle-Roller Thrust Bearings
Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | OD | Thick. | Washer Material | Specifications Met | Each | |
| 110mm | 145mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 000000 |
Bearing Retaining Nuts
Often paired with spring lock washers to strengthen their hold, these retaining nuts—also known as shaft nuts—keep vibration from shifting bearings, bushings, pulleys, and gears on your threaded shaft or spindle. They have slotted sides, so you can tighten and loosen them with a spanner wrench or spanner socket. Made of carbon steel, they’re strong and wear resistant.
Chamfered-face retaining nuts weigh less and produce less heat than stepped-face nuts. They meet ISO 2982 (formerly DIN 981), an international standard for bearing locknut dimensions. Their sizes correspond to SKF KM series. Use them with DIN 5406 spring lock washers.
For technical drawings and 3-D models, click on a part number.