150 mm OD Bearings | McMaster-Carr

Smoother than smooth—the balls inside these bearings roll nearly friction-free. You’ll often find them on rapidly rotating parts, from the whirring chuck on a power drill to the spinning shaft on an electric motor.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Shielded







				Steel

				70	150	35	3	24,900	5,000	-20	230	Standard	6314-2Z	0000000	0000000


				85	150	28	3	19,550	4,500	-20	230	Standard	6217-2Z	0000000	000000


				Sealed







								Steel

								70	150	35	3	24,900	3,000	-30	210	Standard	6314-2RS	0000000	000000


								85	150	28	3	19,550	2,800	-30	210	Standard	6217-2RS	0000000	000000

Spherical-Roller Bearings

Two rows of rollers give these bearings dynamic radial load capacities over five times higher than comparably sized tapered-roller bearings. Also known as rock crusher bearings, they handle heavy shock loads and are used for metal milling machinery, mining and oil field equipment, and in paper mills.

						Combined Load Cap., lbf
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Bearing Trade No.	Ring Material	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	Max. Temp., ° F		Each
Open Bearing



		70	150	51	22314	Steel	87,500	87,500	4,800	Required	212	0000000	0000000


		85	150	36	22217	Steel	69,500	73,000	3,400	Required	390	0000000	000000

Maintenance-Free Turntable Bearings

With low-friction internal sleeves made of PTFE, these bearings never need lubrication. Also known as slewing-ring bearings, they’re used for slow, controlled rotation. You’ll often see them rotating hoists, robotic arms, and other heavy machinery. They have holes on both the inner and outer ring, so they’re easy to align and mount.

Note: Listed capacities only apply when bearings are mounted parallel to the ground. These bearings can be mounted in other orientations, but their capacities will be reduced.

	Thrust Load Cap., lb.		Radial Load Cap., lb.							Bearing
	Dynamic	Static	Dynamic	Static	Static Moment Load Cap., ft·lbf	OD, mm	ID, mm	Overall Ht., mm	Material	Type	Material	Plain Bearing Type	Mounting Fasteners Included		Each
For Combined Radial, Thrust, and Moment Loads



		2,200	8,950	560	1,750	440	150	50	33	Anodized Aluminum	Plain	PTFE	Sleeve	No	0000000	0000000

High-Load Crossed-Roller Bearings

The thicker inner and outer raceways on these bearings can handle heavier loads than the thin-profile crossed-roller bearings. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.

Open Bearing—Open bearings dissipate heat more efficiently than sealed bearings.

Sealed Bearing—Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.

				Combined Load Cap., lbf
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	Temp. Range, ° F	Features		Each
For Combined Radial, Thrust, and Moment Load—Open with Steel Ring



		100	150	20	11,400	16,200	600	Required	0 to 245	—	0000000	0000000


		For Combined Radial, Thrust, and Moment Load—Sealed with Steel Ring



				100	150	20	11,400	16,200	480	Lubricated	0 to 245	Lubrication Groove, Two Lubrication Holes	0000000	000000

Static-Control Maintenance-Free Turntable Bearings

Image of Product. Front orientation. Turntable Bearings. Maintenance-Free, Static Control.

Safe enough to rotate equipment in microchip and semiconductor manufacturing, these bearings prevent harmful static buildup. They’re made from stainless steel and have specially formulated PTFE sleeves that work together to drain static. Make sure your set up provides a path to the ground.

Also known as slewing-ring bearings, these bearings are great for turning heavy equipment in a slow and controlled way. Their sleeves are also slippery, so they move smoothly and don't require lubrication. For alignment and mounting, they have holes on both the inner and outer ring.

Note: Listed capacities only apply when bearings are mounted parallel to the ground. These bearings can be mounted in other orientations, but their capacities will be reduced.

	Thrust Load Cap., lb.		Radial Load Cap., lb.							Bearing
	Dynamic	Static	Dynamic	Static	Static Moment Load Cap., ft·lbf	OD, mm	ID, mm	Overall Ht., mm	Material	Type	Material	Plain Bearing Type	Mounting Fasteners Included	Performance		Each
For Combined Radial, Thrust, and Moment Loads



		2,200	8,950	560	1,750	440	150	50	33	Stainless Steel	Plain	PTFE	Sleeve	No	Antistatic	00000000	000000000

Bearing Nuts

Carbon Steel

Chamfered Face

Often paired with spring lock washers to strengthen their hold, these bearing nuts—also known as shaft nuts—keep vibration from shifting bearings, bushings, pulleys, and gears on your threaded shaft or spindle. They have slotted sides, so you can tighten and loosen them with a spanner wrench or spanner socket.

Carbon Steel—Carbon steel bearing nuts are strong and resist wear.

Chamfered Face—Chamfered-face bearing nuts weigh less and produce less heat than stepped-face nuts.

ISO 2982— Some chamfered-face bearing nuts meet ISO 2982 (formerly DIN 981), an international standard for bearing locknut dimensions. Their sizes correspond to SKF KM series. Use them with DIN 5406 spring lock washers.

Thread Spacing—When choosing your thread spacing, consider the precision of your application. The finer the threads, the more control you have when making adjustments.

	Nuts								Bearing Lock Washers
	Thread
	Size	Spacing	OD, mm	Wd., mm	Specs. Met	For Lock Washer Specs. Met		Each		Each
Carbon Steel







				Chamfered Face

				M115 × 2 mm	Extra Fine	150	19	DIN 981, ISO 2982	DIN 5406	0000000	000000	000000000	000000