System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
OD OD | Show |
|---|
|
OD OD | Hide |
|---|
ID ID |
|---|
|
For Load Direction For Load Direction |
|---|
 | Thrust |
Dynamic Thrust Load Capacity Dynamic Thrust Load Capacity |
|---|
|
For Shaft Type For Shaft Type |
|---|
 | Round |
Cage Material Cage Material |
|---|
|
Ball Bearing Type Ball Bearing Type |
|---|
 | Standard |
Ball Material Ball Material |
|---|
|
Static Thrust Load Capacity Static Thrust Load Capacity |
|---|
|
Seal Type Seal Type |
|---|
|
Washer Material Washer Material |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Lubrication Lubrication |
|---|
|
Thread Size Thread Size |
|---|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
About Ball and Roller Bearings
More
About Shaft Collars
Shaft collars are useful for holding and positioning components on a shaft. They can also serve as mechanical stops and stroke limiters.
More
Thrust Ball Bearings
Steel balls and washers allow these bearings to handle higher loads than bearings with stainless steel components. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
Bearings with steel cage and with bronze cage handle higher loads and speeds than bearings with a plastic cage.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Cage Material | Washer Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Includes | Each | |
Open | ||||||||||||
| 120mm | 155mm | 25mm | Steel | Steel | 20,000 | 69,600 | 2,200 | Required | -40° to 250° | Two Washers | 00000000 | 0000000 |
Needle-Roller Thrust Bearings
Thinner rollers allow these bearings to fit in tighter spaces than tapered-roller thrust bearings. Because of the large contact area between the rollers and washers (not included), these bearings are great for medium to heavy duty, low-friction jobs. For use on hardened and ground surfaces.
Washers allow you to use the bearing on unhardened and unground surfaces.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microns | Temp. Range, °F | Specifications Met | Each | |
Steel Rollers | |||||||||||
Open | |||||||||||
| 120mm | 155mm | 4mm | 22,900 | 152,800 | 2,070 | Required | 0.2 | 0° to 240° | DIN 5405-3, ISO 303 | 00000000 | 0000000 |
| For Shaft Dia. | OD | Thick. | Washer Material | Specifications Met | Each | |
| 120mm | 155mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 000000 |
Washers for Needle-Roller Thrust Bearings
Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | OD | Thick. | Washer Material | Specifications Met | Each | |
| 120mm | 155mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 000000 |
Bearing Retaining Locknuts
With a nylon insert that grips your threaded shaft or spindle without damaging its threads, these locknuts—also called shaft nuts—hold bearings, bushings, gears, and pulleys prone to vibration tightly in place. They come as one piece, so you can easily clamp them onto your shaft or spindle. But, since they aren’t made entirely of metal, they don’t stand up to heat as well as all-metal locknuts. Slots in their sides mean you can tighten and loosen them with a spanner wrench or spanner socket. Their face is also chamfered to help keep the size and weight of your assembly at a minimum. All meet international standards for bearing locknut dimensions.
When choosing your thread spacing, consider the precision of your application. The finer the threads, the more control you have when making adjustments.
All carbon steel locknuts are strong and resist wear, though they don’t stand up to corrosion as well as stainless steel locknuts.
For technical drawings and 3-D models, click on a part number.
Thread | Carbon Steel | |||||||
|---|---|---|---|---|---|---|---|---|
| Size | Pitch, mm | Spacing | OD | Wd., mm | Insert Max. Temp., °F | Specifications Met | Each | |
Chamfered Face | ||||||||
| M120 | 2 | Extra Fine | 155mm | 23 | 160° | ISO 2982-2 | 00000000 | 0000000 |
Bearing Retaining Nuts
Often paired with spring lock washers to strengthen their hold, these retaining nuts—also known as shaft nuts—keep vibration from shifting bearings, bushings, pulleys, and gears on your threaded shaft or spindle. They have slotted sides, so you can tighten and loosen them with a spanner wrench or spanner socket. Made of carbon steel, they’re strong and wear resistant.
Chamfered-face retaining nuts weigh less and produce less heat than stepped-face nuts. They meet ISO 2982 (formerly DIN 981), an international standard for bearing locknut dimensions. Their sizes correspond to SKF KM series. Use them with DIN 5406 spring lock washers.
For technical drawings and 3-D models, click on a part number.