System of Measurement System of Measurement |
|---|
|
OD OD | Show |
|---|
|
OD OD | Hide |
|---|
For Load Direction For Load Direction |
|---|
 | Combined Radial and Thrust |
 | Thrust |
For Housing ID For Housing ID |
|---|
|
Static Thrust Load Capacity Static Thrust Load Capacity |
|---|
|
Static Combined Load Capacity Static CombinedLoad Capacity |
|---|
|
Bearing Type Bearing Type |
|---|
 | Roller |
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Bearing Trade Number Bearing Trade Number |
|---|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Roller Material Roller Material |
|---|
|
For Shaft Type For Shaft Type |
|---|
 | Round |
Lubrication Lubrication |
|---|
|
Seal Type Seal Type |
|---|
|
Cage Material Cage Material |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
About Ball and Roller Bearings
More
About Shaft Collars
Shaft collars are useful for holding and positioning components on a shaft. They can also serve as mechanical stops and stroke limiters.
More
Spherical-Roller Bearings
Two rows of rollers give these bearings dynamic radial load capacities over five times higher than comparably sized tapered-roller bearings. Also known as rock crusher bearings, they handle heavy shock loads and are used for metal milling machinery, mining and oil field equipment, and in paper mills.
For technical drawings and 3-D models, click on a part number.
Combined Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Bearing Trade Number | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Max. Temp. Range, °F | Each | |
Open | |||||||||||
| 110 | 200 | 53 | 22222 | Steel | 136,000 | 145,000 | 2,600 | Required | 390 | 0000000 | 0000000 |
Needle-Roller Thrust Bearings
Thinner rollers allow these bearings to fit in tighter spaces than tapered-roller thrust bearings. Because of the large contact area between the rollers and washers (not included), these bearings are great for medium to heavy duty, low-friction jobs. For use on hardened and ground surfaces.
Washers allow you to use the bearing on unhardened and unground surfaces.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microns | Temp. Range, °F | Specifications Met | Each | |
Steel Rollers | |||||||||||
Open | |||||||||||
| 160mm | 200mm | 5mm | 33,200 | 229,300 | 1,590 | Required | 0.2 | 0° to 240° | DIN 5405-3, ISO 303 | 00000000 | 0000000 |
| For Shaft Dia. | OD | Thick. | Washer Material | Specifications Met | Each | |
| 160mm | 200mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 0000000 |
Washers for Needle-Roller Thrust Bearings
Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | OD | Thick. | Washer Material | Specifications Met | Each | |
| 160mm | 200mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 0000000 |
Bearing Retaining Nuts
Often paired with spring lock washers to strengthen their hold, these retaining nuts—also known as shaft nuts—keep vibration from shifting bearings, bushings, pulleys, and gears on your threaded shaft or spindle. They have slotted sides, so you can tighten and loosen them with a spanner wrench or spanner socket. Made of carbon steel, they’re strong and wear resistant.
Chamfered-face retaining nuts weigh less and produce less heat than stepped-face nuts. They meet ISO 2982 (formerly DIN 981), an international standard for bearing locknut dimensions. Their sizes correspond to SKF KM series. Use them with DIN 5406 spring lock washers.
For technical drawings and 3-D models, click on a part number.
Thread | ||||||||
|---|---|---|---|---|---|---|---|---|
| Size | Pitch, mm | Spacing | OD, mm | Wd., mm | Specifications Met | For Lock Washer Specifications Met | Each | |
Carbon Steel | ||||||||
Chamfered Face | ||||||||
| M155 | 3 | Extra Fine | 200 | 25 | DIN 981, ISO 2982 | DIN 5406 | 0000000 | 0000000 |