System of Measurement System of Measurement |
|---|
|
OD OD | Show |
|---|
|
OD OD | Hide |
|---|
Rod End Type Rod End Type |
|---|
 | Swivel Joint |
Static Radial Load Capacity Static Radial Load Capacity |
|---|
|
Static Thrust Load Capacity Static Thrust Load Capacity |
|---|
|
Material Material |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
Ball Material Ball Material |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Seal Material Seal Material |
|---|
|
Insert Material Insert Material |
|---|
|
Lubrication Lubrication |
|---|
|
Maximum Torque Maximum Torque |
|---|
|
Shaft Mount Type Shaft Mount Type |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
About Rod Ends
More
Extended-Life Swivel Joints
Specially designed lubrication channels and integral seals allow these joints to last up to three times longer than other swivel joints. Also known as spherical bearings, they support angular misalignment. Press into a hole or housing where a ball joint rod end won’t fit. All have seals to keep grease in and contaminants out. Joints come greased and can be lubricated through a hole in the housing without removing the load.
For technical drawings and 3-D models, click on a part number.
| ID | OD | O'all Thick. | Housing Thick. | Max. Ball Swivel | Static Radial Load Cap., lbs. | Max. Temp., °F | Material | Each | |
| 2" | 3 3/16" | 1 3/4" | 1 1/2" | 14° | 150,900 | 250° | Bearing Steel | 0000000 | 0000000 |
Thrust-Rated Swivel Joints
A unique design allows these joints to support heavy one-direction thrust loads as well as combined radial/thrust loads. Also known as spherical bearings, you can press them into tight spots where a rod end shank won’t fit or mount them in a drilled hole or a rod end blank. Lubrication is required.
For technical drawings and 3-D models, click on a part number.
| ID | OD | O'all Thick. | Housing Thick. | Static Radial Load Cap., lbs. | Static Thrust Load Cap., lbs. | Material | Each | |
| 2" | 3 3/16" | 1 1/4" | 15/16" | 82,500 | 91,700 | Bearing Steel | 0000000 | 0000000 |
Flush-Mount Screw-Clamp Bushings
Insert these bushings into the bore of your sprocket for flush or recessed mounting. They handle shock loads and have higher torque ratings than self-centering bushings. When you tighten the included clamping screws, the bushing's inner sleeve contracts onto the shaft and the outer sleeve expands to hold your sprocket, pulley, or gear. They can be mounted on shafts with or without keyways.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | OD | Overall Wd. | Max. Torque, in.-lbs. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
| 1 15/16" | 3 3/16" | 1 17/64" | 15,400 | 360 | Steel | Clamping Screws | 0000000 | 000000 |