Make quick, shallow cuts with these short blades.

The blade edge is sharper than other razor blades for fine, precise cuts.

Cut without contaminating your workpiece.

Use on hard-to-cut materials such as Kevlar and rubber.

These durable knives have a large, metal handle that withstands the force needed to cut through tough materials.

The handle is large, fluted, and made of lightweight plastic so it's easy to hold while applying pressure.

Cut curves and circles with a blade that rotates 360°.

Cut, trim, and puncture thin materials such as paper, plastic, and fabric.

Snap off dull blade segments to expose a sharp edge for precise cuts.

Cut cardboard, paper, plastic, and other packaging material in your food processing plant.

An angled aluminum handle gives you control, even in hard-to-reach places.

Blades rotate to cut curves and shapes on flat surfaces.

This manual-lock knife has a sliding lock to hold the blade in place.

Cut thin, synthetic material up to 5/8" thick.

These blades have a heat-resistant coating to prevent material buildup.

Also known as dado-head blades, these are for cutting grooves in all types of wood.

Square-shaped teeth cut across the grain and with the grain (ripping) in reclaimed lumber and flooring with embedded nails.

A continuous edge on these blades produces smooth cuts. It's coated in diamond grit to cut hard, abrasive materials such as masonry, stone, asphalt, and concrete.

A continuous edge on these blades produces smooth cuts.

A blend of tungsten carbide and diamond grits on the continuous edge of these blades cuts hard, nonmetallic materials including composites and graphite.

Make clean cuts in rubber and plastic hose with the scalloped knife edge on these blades.

A razor-sharp knife edge minimizes dust and makes quick, clean cuts through foam sheets such as expanded polystyrene insulation and extruded polystyrene.

Make fast, clean cuts in steel sheets, angle iron, rebar, and pipe with the carbide teeth on these blades.

Prevent clogging when cutting soft metal—these blades have plenty of space between the carbide-tipped teeth to allow chips to escape.

These blades have a heat-resistant coating to prevent material buildup.

Also known as rip blades, these steel blades have large, forward-angled, carbide-tipped teeth for making fast cuts.

Use these blades for occasional cutting.

The edge of the blade is segmented to cut faster than a continuous edge.

The edge of the blade is segmented to cut faster than a continuous edge.

Use with water or coolant to produce smoother cuts in tile than dry-cutting blades. They're also for use on glass.

Make clean cuts in rubber and plastic hose with the scalloped knife edge on these blades.

The carbide-grit edge on these blades cuts brittle and abrasive materials including glass and fiberglass.

Make fast, clean cuts in steel sheets, angle iron, rebar, and pipe with the carbide teeth on these blades.

Diamond grit bonded to a segmented edge cuts through hard metal such as cast iron.

These blades have a continuous edge with diamond grit to cut through ceramics.

A tungsten carbide grit edge cuts through abrasive materials such as composites and fiberglass.

These blades have a higher concentration of diamonds than other dry-cutting blades, so they last up to three times longer.

Use these titanium carbonitride (TiCN) coated blades on stainless steel.

The teeth on these blades are set in a pattern specially designed to cut faster than other blades for metal.

These blades are wide to cut through multiple layers. They're also known as demolition blades.

A pointed tip makes plunge cuts in metal.

Tooth size and number per inch are constant throughout these blades.

Teeth are coated with titanium nitride (TiN) for wear resistance and longer life than uncoated teeth.

These wide blades cut through multiple layers. They're also known as demolition blades.

Tooth size and number per inch are constant throughout the blade.

Produce smooth cuts—the teeth vary in size and pattern to reduce vibration. They're also known as variable-set blades.

Teeth are V-shaped teeth to cut on forward and backward strokes for fast cuts.

These blades are stiffer than other blades for making straight cuts in wood.

Carbide grit is bonded to the edge of these steel blades.