Ball bearings operate with less friction than other bearings, so they can run at higher speeds.

Also known as tapped-base bearings, these ball bearings mount to surfaces from the bottom through threaded holes. Because of their narrow profile, they’re commonly used in tight-clearance spaces, including systems where multiple shafts are mounted close together.

A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication.

Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants.

Use these bearings in corrosive environments and under water.

Capable of handling temperatures from -400° to 750° F, these graphalloy bearings withstand the widest temperature range of any of our mounted bearings.

These nylon bearings swivel inside their housing to compensate for over 20° of shaft misalignment.

Made of acetal blended with PTFE, these bearings handle speeds twice as fast as standard sleeve bearings.

A strong steel housing allows these bearings to handle higher speeds than standard oil-embedded mounted sleeve bearings.

A bolt in each corner makes for a secure, even hold.

Made to withstand frequent washdowns, these bearings are permanently lubricated, which means you’ll never have to add lubricant. Use them in hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants.

Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings with four-bolt flange.

The tapered rollers in these bearings support large shafts at high static loads.

Ball bearings operate with less friction than other bearings, so you can run them at higher speeds.

The lubricant in these mounted ball bearings is suitable for incidental contact with food.

Use these bearings in corrosive environments and under water.

These bearings have the highest speed ratings of any mounted ball bearing in our offering.

Embedded lubricant particles increase the load capacity of these bearings while also making them slippery.

Capable of handling temperatures from -400° to 750° F, these graphalloy bearings have the widest temperature range of any of our mounted bearings.

Made of FDA listed PEEK, these bearings are suitable for direct contact with food. The closed backing blocks out dust and other contaminants.

Use one of these base-mount housings with your own bearing to create a custom mounted bearing.

Quickly mount bearings in these precision-flanged housings, no machining required.

Outdoor as well as mild chemical environments are no problem for these bearings. They have stainless steel balls for corrosion resistance.

Mount these bearings on a support rail shaft for applications requiring maximum rigidity.

With two bearings mounted in a single housing, these bearings have higher load capacities than standard ones. A ceramic liner helps them achieve high speeds as well as rapid acceleration and deceleration.

Choose ball bearings for debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

Outdoor as well as mild chemical environments are no problem for these bearings. They have stainless steel balls for corrosion resistance.

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

With two bearings mounted in one housing, these sleeve bearings can handle heavier loads than standard mounted linear sleeve bearings.

With two bearings mounted in a single housing, these bearings have load capacities more than 10 times as high as standard mounted linear sleeve bearings. A ceramic liner helps them achieve high speeds as well as rapid acceleration and deceleration.

The shell, housing, and balls of these bearings are stainless steel for excellent corrosion resistance.

The Frelon liner on these bearings allows them to stand up to a wider range of chemicals than other flange-mounted linear sleeve bearings.

Slide up to two linear ball or sleeve bearings into these housings and secure them with the included internal retaining rings.

Combine with a machine key to transmit torque to gears, sprockets, and other power transmission components.

Connect these internally threaded shafts directly to threaded components, or use a fastener to secure. They have a flat surface area that allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.

In addition to diameter tolerances that are twice as tight as standard keyed shafts, these shafts include a traceable lot number and test report. Use them with machine keys to transmit torque to gears, sprockets, and other power transmission components.

Eight times straighter than standard rotary shafts, these tight-tolerance shafts minimize vibrations and reduce wear to bearings and other components. They also have diameter tolerances that are twice as tight as standard rotary shafts.

Attach threaded accessories, such as mixer propellers and fan blades, to the end of these shafts.

Thread these shafts into a tapped hole to support idler sprockets and pulleys in tensioning applications. They have a retaining-ring groove, retaining ring, and spacers to position your component and hold it in place.

With a splined profile on one end, these shafts transmit high rotational loads—good for hydraulic systems, machine tools, and other high-torque applications. Compared to keyed shafts, they last longer, handle higher torque, and do not require as tight of a fit.