These clamps form a 360° seal around your hose or tube to prevent leaks.

A double ring of thick wire provides a complete seal around large-diameter hose.

The T-bolt design provides excellent strength and creates a 360° seal. Clamps have a spring that automatically adjusts the clamp diameter when temperatures fluctuate.

The hose clamps in these assemblies have a bolt closure that creates a 360° leak-preventing seal. The clamps have rolled edges, so they won’t cut into soft hose and tube materials such as silicone.

Connect quick-clamp sanitary tube fittings—also known as aseptic fittings—for a fast and easy way to access your line.

Eliminating the need for step blocks or other rear support, the pivoting rocker clamps workpieces of various thicknesses.

Use with T-slot nuts or bolts and a support to secure a workpiece, vise, or fixture to a machine table.

Designed to provide more clearance above the nut than standard clamps, these have an offset shape. Also known as gooseneck clamps.

Position these clamps between two workpieces, vises, or fixtures and secure both to your machine table using T-slot nuts or bolts.

Good for occasional machining, economy kits contain lower-strength components than standard kits.

Get everything needed for basic workholding on a machine table.

Use these blocks to support setup clamps. Fit the nonslip steps together for quick height adjustments.

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

Smaller than standard setup clamps, these clamps leave more usable space on a machine table when mounting a vise.

With no handle or protruding screw, these clamps can fit into tight spaces.

These clamps have twice the capacity of standard C-clamps.

Lighter weight than other metal clamps, these are less likely to bend thin material.

All components of these clamps are made of aluminum-bronze that is Factory Mutual approved. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

A bright finish makes these clamps easy to see.

Three screws apply pressure to three sides of a workpiece.

The jaws move in unison to apply even pressure and prevent twisting.

Plastic clamping surfaces prevent damage to material.

The spring-loaded tips on these clamps swivel in all directions to make maximum contact with angled and uneven workpieces.

Hold a workpiece securely from the side with minimal contact, leaving more of the workpiece free for machining.

Machine these clamps to match the contours of your workpiece and turn the screw to grip.

Machine these fixture clamps to match the contours of your workpiece for a stronger grip.

Set one of these clamps between two workpieces in a fixture and tighten the screw to push the clamp's sides out for a secure hold.

These clamps wedge against the workpiece ID to grip cast, unfinished, or uneven parts, leaving the outside clear for machining.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Push the lever to lock the handle and prevent accidental opening.

The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.

Push the lever to lock the handle and prevent accidental opening.

Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.

Mount these clamps to a bench top or other surface to keep workpieces in place.

Push the lever to lock the handle and prevent accidental opening.

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

The mounting base secures these clamps to a rail or bar.

These clamps have mounting holes on the bottom.

The large, flat jaws remain parallel when clamping to apply even pressure without denting or marring the workpiece. Pull the handle to lock or release the clamping arm.

Each arm slides freely for quick, one-handed positioning. They lock when the screws are tightened onto a workpiece.

Pull the handle to lock the jaw in place and prevent loosening caused by vibration.

Place the arms on a pipe that is threaded at one end and at least 12" long to create your own bar clamp.

Two swivel pads on each jaw pivot to grip nearly any shape of material.

Attach to your bar clamp to hold material on three sides.

Pull the lever to slide the clamping arm along the bar; release to lock in place.

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol-grip handle to lock the clamp in place.

Also known as clamping handles, use these standard adjustable handles for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten.

A soft textured surface provides a comfortable grip for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten. These handles are also known as clamping handles.

Choose these handles when vertical space is limited. Also known as clamping handles, use them for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten.

With a surface resistivity of 10,000 ohms, these handles reduce static electricity that can damage electronic equipment. Also known as clamping handles, use them for applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten.

Made of stainless steel with a nitrile mounting seal, these handles are suitable for food-processing applications involving frequent positioning, tightening, and holding adjustments. Lift the handle to rotate freely; then release the handle to engage and tighten. These handles are also known as clamping handles.

Identify equipment controls and components at a glance by their color. Mount these knobs into a threaded hole. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

A rubber coating provides a comfortable grip to position, tighten, and hold fixtures, equipment, and machinery. Mount these knobs into a threaded hole.

Made for use in food processing facilities, these plastic knobs have a metal additive that sets off metal detectors if a piece breaks off into your line.

Suitable for food-processing areas, these one-piece knobs have no joints to collect dirt or debris. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery. Mount them into a threaded hole.

The domed top allows you to firmly hold these knobs in the palm of your hand to position, tighten, and hold fixtures, equipment, and machinery. Mount them into a threaded hole.

Also known as muffler clamps, these U-bolts have a rounded mounting plate that fully surrounds pipe, conduit, and tubing for a secure fit.

Secure items to either side of these collars—each half has a flat end with a tapped hole

Attach items to tapped holes at either end of these collars and twist the lever to quickly move them along shafts.

A large swivel angle allows these thumb screws to make better contact with angled and uneven surfaces than nonremovable swivel-tip thumb screws.

A wide tip provides more gripping power than standard swivel-tip thumb screws. To use, remove the tip, thread the screw through the hole, and attach the tip on the other side.

Arms provide a flat surface to push your fingers against.

Made from 18-8 stainless steel, these thumb screws are chemical resistant. Also known as dog- and pilot-point thumb screws, insert the point into a drilled hole or slot to hold items in place.

A large head allows you to grip these screws with your entire hand for greater torque while tightening than standard knurled plastic-head thumb screws.

These metric thumb screws have a large head that allows you to grip them with your entire hand for greater torque while tightening than standard knurled plastic-head thumb screws.

Tighten these thumb screws by hand or with a hex key for more torque.