Choose these screws for their adherence to strict military standards for material and construction.

Tighten these screws by turning them to the left; once fastened, they prevent counterclockwise-moving parts from loosening.

Choose these screws for their adherence to strict military standards for material and construction. Screws are 18-8 stainless steel for good chemical resistance.

Cleaned and double bagged in an ISO Class 5 (Fed. Std. Class 100) clean room, these screws are ready to use on chambers and components in high-vacuum systems.

Often used to fasten parts in engines and turbines, these are our strongest stainless steel screws. They are comparable in strength to alloy steel with the corrosion resistance of 18-8 stainless steel.

Plastic screws are chemical and oil resistant, nonconductive, and lightweight.

Our most corrosion-resistant metal screws, titanium screws withstand salt water, acids, and chemicals. They have a high strength-to-weight ratio and are about 40% lighter than steel screws.

More corrosion resistant than stainless steel screws, nickel alloy screws have excellent resistance to salt water and some acids.

Nearly as strong as steel, these stainless steel screws won’t rust in outdoor, washdown, and other corrosive environments. With half the height of a standard socket head, these low-profile screws fit in tight spaces.

Made from alloy steel, these screws are nearly twice as strong as stainless steel low-profile screws. With a head height one-third the size of a standard socket head, they fit in the tightest spaces.

With a head one and a half times taller than a standard socket head, these screws are easier to install in deep counterbored holes and other hard-to-reach places.

These general purpose flanged screws distribute pressure where the screw meets the surface, eliminating the need for a washer.

With a tensile strength of 170,000 psi, these alloy steel screws are among the strongest we carry. They are stronger than Grade 8 steel screws and are more than twice as strong as stainless steel wire-lockable screws. These resist vibration better than any other socket head screw.

These screws have good chemical resistance. A thread locker bonded to the threads prevents loosening from vibration.

With a tensile strength of 180,000 psi, these alloy steel screws are among the strongest we carry. They are stronger than Grade 8 steel screws and more than two and a half times stronger than stainless steel screws with split lock washer. The split lock washer helps to resist vibration.

Drilled through the head and shaft, these screws vent fluid and gases trapped below the screw, making them good for vacuum applications.

Fasten these screws inside a high-vacuum system without bringing in contaminants.

The nylon patch bonded to the threads of these socket head screws adds friction to keep vibration from loosening them, while their O-ring prevents leaks and seals out contaminants.

The nonmarring brass tip is electrically conductive and harder than nylon, but soft enough to conform to most surfaces and reduce damage from metal-on-metal contact.

More corrosion resistant than 18-8 stainless steel screws, these pan head screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

These steel pan head screws are coated for corrosion resistance.

Nylon pan head screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

Polycarbonate screws resist breaking in high-impact applications. All are chemical and oil resistant, nonconductive, and lightweight.

Our most corrosion-resistant screws, these titanium pan head screws withstand salt water, acids, and chemicals. They have a high strength-to-weight ratio.

More corrosion resistant than 18-8 stainless steel screws, these screws have excellent resistance to chemicals and salt water. The extra-wide truss head distributes holding pressure to reduce the likelihood of crushing thin material. Screws may be mildly magnetic.

A zinc plating provides mild corrosion resistance.

More corrosion resistant than 18-8 stainless steel screws, these button head screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

Brass button head screws are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

More corrosion resistant than 18-8 stainless steel screws, these pan head screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

PTFE screws withstand harsh chemicals and temperatures from -100° F to 500° F. They are nonconductive, lightweight, and resist wear due to their slippery surface.

These pan head screws are zinc plated for corrosion resistance in wet environments.

One-third the weight of steel, aluminum screws resist corrosion in wet environments.

More corrosion resistant than 18-8 stainless steel screws, these screws have excellent resistance to chemicals and salt water.

Nylon screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

A zinc plating provides mild corrosion resistance.

More corrosion resistant than 18-8 stainless steel screws, these screws have excellent resistance to chemicals and salt water.

Brass screws are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

Brass screws are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

A zinc plating provides mild corrosion resistance.

Made from alloy steel, these screws are three times stronger than standard steel button head Torx screws. A Torx-Plus drive has more points of contact than other drives, allowing you to tighten the screw without damaging the recess.

These screws have a Torx or Torx-Plus drive for more points of contact than other drives, allowing you to tighten the screw without damaging the recess.

Made from 18-8 stainless steel, these screws have good chemical resistance and may be mildly magnetic. Torx and Torx-Plus drives have more points of contact than other drives, allowing you to tighten the screw without damaging the recess.

These screws have a tall, domed head that provides a finished appearance. They're zinc plated to resist corrosion in wet environments.

18-8 stainless steel screws have good chemical resistance and may be mildly magnetic. The flange distributes pressure across a wide surface, eliminating the need for a separate washer.

These aluminum screws are lightweight and resist corrosion in wet environments. They have a flange that is wider and thicker than our other flanged screws, so they distribute pressure the best.

Comparable in diameter to a washer, the flange on these screws distributes pressure better than standard flanged screws. Made from 316 stainless steel, they have excellent resistance to chemicals and salt water. Screws may be mildly magnetic.

To prevent unwanted removal, these screws have a tamper-resistant Torx drive—also known as a pin-in Torx drive—that makes them difficult to unscrew without special tools. An O-ring under the head blocks leaks and seals out dust and dirt.

The extra-wide head distributes holding pressure to reduce the likelihood of crushing thin materials.

Made from alloy steel, these screws are nearly twice as strong as stainless steel button head screws.

Stainless steel screws have excellent corrosion resistance in most environments.

A zinc plating provides mild corrosion resistance.

Made from stainless steel, these screws have good chemical resistance and may be mildly magnetic. All have a washer with sharp external teeth that dig into surfaces for maximum holding power and vibration resistance. Also known as Sems screws, the washer rotates freely but is permanently attached.

These stainless steel screws have good chemical resistance and may be mildly magnetic. The washer has sharp internal teeth that dig into surfaces to resist large amounts of vibration while the smooth outside edge provides a finished look. Also known as Sems screws, the washer rotates freely but is permanently attached.

A zinc plating provides mild corrosion resistance.

When compressed, the split lock washer flattens to add tension and prevent loosening from small amounts of vibration. Also known as Sems screws, the washer rotates freely but is permanently attached.

Made from alloy steel, these screws are nearly twice as strong as stainless steel button head screws.

A nylon patch bonded to the threads adds friction to prevent loosening from vibration. Made from 18-8 stainless steel, these screws have good chemical resistance and may be mildly magnetic.

Wire these screws together through the hole in the head for better vibration resistance than any other rounded head screw.

A nylon patch bonded to the threads adds friction to resist loosening from vibration.

When clearance for a wrench is limited, these screws have a Phillips drive so you can install them with a screwdriver. They are used for high-strength fastening.

Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.

Plastic screws are chemical and oil resistant, nonconductive, and lightweight.

Made from Grade 5 steel, these screws are suitable for fastening most machinery and equipment. Serrations under the flange provide mild vibration resistance.

Install these screws with a wrench or a screwdriver. Made from stainless steel, they have good corrosion resistance. A flange under the head means a separate washer is not necessary.

An O-ring under the head prevents leaks and seals out contaminants.

Choose these screws for their adherence to strict military standards for material and construction.

More corrosion resistant than 18-8 stainless steel screws, these screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

Brass screws are electrically conductive, nonmagnetic, and have good corrosion resistance.

More corrosion resistant than 18-8 stainless steel screws, these screws have excellent resistance to chemicals and salt water.

These steel screws have a zinc plating for mild corrosion resistance.

Brass screws are electrically conductive, nonmagnetic, and have good corrosion resistance.

Our most corrosion resistant screws, titanium screws withstand salt water, acids, and chemicals.

These screws are more reliable in high-stress, high-temperature environments than other plastic screws. They withstand water, steam, and temperatures up to 500° F.

PTFE screws are more chemical resistant than other plastic screws and withstand temperatures from -100° F to 500° F.

More corrosion resistant than 18-8 stainless steel screws, these screws have excellent resistance to chemicals and salt water. They may be mildly magnetic.

A zinc plating provides mild corrosion resistance.

Made of 18-8 stainless steel, these screws have good chemical resistance and may be mildly magnetic.

These 18-8 stainless steel screws have good chemical resistance and may be mildly magnetic.

A286 stainless steel screws have comparable strength to alloy steel with the corrosion resistance of 18-8 stainless steel.

Prevent unwanted removal, leaks, and contamination with these sealing Torx screws.

A tamper-resistant hex drive (also known as pin-in hex drive) makes these screws difficult to remove without special tools.

Made from alloy steel, these screws are nearly twice as strong as stainless steel flat head screws.