Also known as angle brackets.

Connect wood 2×4s to posts and other flat surfaces.

Interlock brackets to secure panels flush to flat surfaces.

Connect T‐slotted rails and reinforce joints for structural stability.

Push these brackets into strut channel and tighten the included cam screws for a partially concealed connection.

Mount a length of strut channel between the ends of a beam to run cable and conduit along the beam without drilling.

Support the corners of strut channel structures.

Serrated grooves grip the lip of the channel.

Also known as insert nuts, these convert slotted holes to threaded round holes and keep them centered in the channel.

Create continuous runs of channel without corners.

Rails are drilled with consistently spaced holes for multiple mounting options that do not require machining. Use this steel bolt-together framing to build guards, tables, and racks.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Route pipe, tubing, and conduit across strut channel.

Hold pipe, tubing, and conduit away from strut channel.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.

Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.

A mounting plate provides a more secure hold at the mounting surface.

Suspend and route flat-bottomed objects such as strut channel and small duct.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.

Fasten these brackets to ceilings, walls, beams, and joists to hang threaded rod.

A secure way to hang threaded rod from a pair of angles, such as those used in ceiling joists, without the need to drill or weld. These clamps are commonly used to suspend HVAC, conveyor, and other overhead systems.

Also known as purlin clamps, these clamps are shaped to fit around beams that have a 45° or 90° lip.

Add a crossbeam for hanging lifting equipment, creating overhead conveyor systems, and supporting structural applications.

Support strut channel at a right angle to the beam.

Keep multiple bundles of wire and cable on separate hooks. The hooks have wide openings to allow access for installation, adjustment, and removal.

Temporarily mount routing rings and other threaded components to steel and iron surfaces.

Sew webbing onto these plates for a permanent anchor point or run webbing through to use them as guides.

Attach webbing to these buckles without sewing.

These slides are rated for heavy duty applications.

Hang larger, heavier items than standard hooks with these load-rated hooks.

Quickly mount these hooks with a few strikes of a hammer.

With threads on one end, screw eyes can be easily screwed into wood. They are often used with wire to hang pictures.

These brackets allow you to lower your shelf 10 or 20 degrees.

Design a complete shelving unit with these standards, shelf brackets, and metal shelves. All components are corrosion resistant and are often used for quality control, laboratory, and food service applications.

These standards and shelf brackets are more stable and hold heavier loads than single-slotted standards and brackets.

Use these brackets for extra mounting space behind DIN rail to accommodate wiring and bulky items.

Customize component placement without drilling leaky holes—these channels screw into the mounting bosses in your enclosure.

Curved track pieces allow you to create a wide variety of layouts for doors, curtains, and strip doors.

Narrow track allows you to hang doors in tight spaces.

Open drawers from either side of a cart or cabinet—these slides let drawers pass through for two-way access to contents.

Also known as ground-joint couplings and boss couplings, these fittings are designed for high-pressure steam applications up to 600 psi. Insert the barbed end of the fitting into hose, then position the interlocking clamp over the hose and bolt into place. The clamp firmly grips your hose as it locks into the ring of the barbed end, creating a leak-tight seal.

These pinch clamps come packed in a box with individual compartments for each clamp size. Easier to install than worm-drive clamps, crimp the pinch points with pinch-clamp pincers for a secure hold. They’re commonly known as ear clamps.

A double ring of thick wire provides a complete seal around large-diameter hose.

These clamps have a wider band than other constant-tension clamps, which provides more coverage and reduces the chance of leaks.

These brackets secure eyelet end fittings from both sides to provide a strong hold on gas springs that get bumped or jostled. Mount on any panel, lid, or door.

Install these sockets in tubing, angle iron, channel, and wood to hold friction-grip stem casters in place.