Machine holes and slots or weld in place.

Machine holes and slots or weld in place.

Machine holes and slots or weld in place.

Often used in washrooms, these brackets mount panels and partitions.

Support wooden handrails on stairs and ramps with these wall-mount brackets.

Use hinges to add doors, lids, and machine guards to T-slotted framing.

Designed to wrap around the sides of strut channel, these brackets provide a stronger hold than other strut channel brackets.

A tab on the end of these shelf brackets fits inside the strut channel for extra stability.

Serrated grooves grip the lip of the channel.

Keep hardware centered in the strut channel slot.

Position two strut channels at a 30° to 60° angle, then tighten the bolt to secure.

Made of 316 stainless steel, this framing has excellent resistance to chemicals and salt water.

Route pipe, tubing, and conduit across strut channel.

Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

Customize these clamps to any object—they have a bend-and-stay design so you can mold them to the size and shape you need. Made of plastic-coated 316 stainless steel, they withstand abrasion, corrosion, and UV rays.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

Support vertical pipes passing through floors.

Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.

Also known as muffler clamps, these U-bolts have a rounded mounting plate that fully surrounds pipe, conduit, and tubing for a secure fit.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.

Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Cut as much strap as you need to hang duct, pipe, and other materials.

For centered load distribution, these clamps grip both sides of the beam and hang threaded rod from the middle.

These clamps have a fixed hanger for rigid connections.

For a secure hold on pipe and conduit suspended above the ground, these supports have a cushioned clamp provides a 360° grip while reducing vibration.

Identify bundles at a glance with these ties that are coated for an additional level of corrosion resistance.

These standards can be surface mounted or flush mounted inside a routed groove.

Clamp around a pipe or tube to guide rope.

Wind rope around these cleats for a secure hold.

Permanently sew webbing onto these hooks.

Attach these hooks to elastic cord to make a tie down.

These brackets mount to the frame of a conveyor to hold guide clamps.

Clamps hold guide rails in place or join ends of a rail together.

Also known as cross blocks, connectors join rods at different angles.

These rods have a bracket on the base so they're ready to mount.

Protect monitors and televisions from environmental damage with these enclosures.

Manually control these standard free-moving lid supports through their full range of motion. Raise or lower the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Keep environments free of contaminants—with plastic bushings, there's no metal-to-metal contact that can release particles as these supports open and close. Manually control these free-moving lid supports through their full range of motion. Raise the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Providing constant resistance through the full range of motion, these supports hold lids open at any angle up to 70° or 90°.

Replace rusty or broken hardware on your toilet partitions without needing to buy the entire component.

Built to withstand corrosive marine environments, track is anodized aluminum and hangers are 316 stainless steel.

These slides fully extend for convenient access to the back of drawers.

Slides only extend 3/4 of the closed length to reduce the chance that a heavy load will tip your cabinet.

These slides automatically pull the drawer closed when it approaches the closed position.

These slides gradually slow the drawer's motion to prevent it from slamming open.

A raised safety collar around the head of the screw prevents your screwdriver from slipping and damaging the hose or tube.

Here's everything you need to make your own 3" diameter and larger custom-length worm-drive clamps.

These pinch clamps come packed in a box with individual compartments for each clamp size. Easier to install than worm-drive clamps, crimp the pinch points with pinch-clamp pincers for a secure hold. They’re commonly known as ear clamps.

Unlike vibration-resistant pinch clamps, these have a torque rating for extra holding power in high-vibration applications. They are also known as high-torque clamps.

Clamps have a slotted hex-head screw that flips up to release the band for quick opening.