Also known as angle brackets.

Connect wood 2×4s to posts and other flat surfaces.

Clamp these brackets to panel edges to quickly assemble crates.

Interlock brackets to secure panels flush to flat surfaces.

Connect T‐slotted rails and reinforce joints for structural stability.

Screw and nut sets or nuts secure brackets and other accessories to rails.

Designed to wrap around the sides of strut channel, these brackets provide a stronger hold than other strut channel brackets.

These brackets have narrow slots compatible with quick-connect clamps for securing pipe and conduit on the channel side of struts without screws or tools.

Mount a length of strut channel between the ends of a beam to run cable and conduit along the beam without drilling.

Support the corners of strut channel structures.

There's no need for additional fasteners with these nuts—they combine a strut channel nut with a spring and a threaded stud.

Add hardware to strut channel without having to hold the washer in place or reach inside the channel.

Brackets mount on the outside of strut channel to allow trolley movement.

Position two strut channels at a 30° to 60° angle, then tighten the bolt to secure.

Create continuous runs of channel without corners.

For compatibility with quick-connect clamps to secure pipe and conduit without screws and tools, this strut channel has narrow slotted holes.

Slip these hangers onto the lip of top-opening strut channel to attach chain, wire rope, pipe, and threaded rod.

Create a four-sided raceway for cable, or give a more finished look to strut channel structures.

Rails are drilled with consistently spaced holes for multiple mounting options that do not require machining. Use this steel bolt-together framing to build guards, tables, and racks.

Fittings come in two pieces to wrap around rails, so you can quickly modify existing structures without disassembling. Use clamp-on framing and fittings to form temporary partitions, modular conveyors, and workstations.

Create posts of varying lengths.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Route pipe, tubing, and conduit across strut channel.

Hold pipe, tubing, and conduit away from strut channel.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

Support vertical pipes passing through floors.

Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.

A mounting plate provides a more secure hold at the mounting surface.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.

Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.

Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.

Fasten these brackets to ceilings, walls, beams, and joists to hang threaded rod.

A secure way to hang threaded rod from a pair of angles, such as those used in ceiling joists, without the need to drill or weld. These clamps are commonly used to suspend HVAC, conveyor, and other overhead systems.

A toothed clip secures these clamps to the beam—no fasteners required.

For centered load distribution, these clamps grip both sides of the beam and hang threaded rod from the middle.

Support strut channel at a right angle to the beam.

Clamp to both sides of a beam to add an anchor point for hoists and other overhead equipment.

Route bundles of wire and cable through a single hook. A wide opening allows access for installation, adjustment, and removal.

Anchor these ringbolts where you need them, then remove the ring when not in use. Once installed, the mounting bolt stays in place. Insert the ring by threading into the mounting bolt; remove by unthreading it.

Mount these ringbolts into a threaded hole, or use the nut for through-hole mounting. The pivoting ring allows material to move freely.

These U-shaped supports allows access to pipe and conduit after installation.

Support lines that expand and contract. The roller on these supports compensates for movement in your line from changing temperatures.

Mount these brackets between two studs to support copper tubing for sink faucets and other water supply fixtures.

Sew webbing onto these plates for a permanent anchor point or run webbing through to use them as guides.

Attach webbing to these buckles without sewing.

These slides are rated for heavy duty applications.

Permanently sew webbing onto these hooks.

The thick wire coil on these hooks makes them stronger than standard hooks.

Use in pairs to support a conveyor roller or package stop.

Brackets are sized to mount sensors and reflectors to a conveyor frame.

Use brackets to hang and join sections of enclosed track.