For Suspending For Suspending |
|---|
 | Threaded Rod |
System of Measurement System of Measurement |
|---|
|
Inside Width Inside Width |
|---|
|
Mounting Location Mounting Location | Show |
|---|
|
Mounting Location Mounting Location | Hide |
|---|
Capacity Capacity |
|---|
|
Finish Finish |
|---|
|
Material Material |
|---|
|
Component Component |
|---|
 | Anchor |
Thickness Thickness |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Number of Washers Included Number of Washers Included |
|---|
|
Washer Material Washer Material |
|---|
|
Specifications Met Specifications Met |
|---|
|
Number of Set Screws Included Number of SetScrews Included |
|---|
|
Angle Iron Clamps for Threaded Rod
A secure way to hang threaded rod from a pair of angles, such as those used in ceiling joists, without the need to drill or weld. These clamps are commonly used to suspend HVAC, conveyor, and other overhead systems. They may also be used to connect two pairs of angles at 90°. Clamps are zinc-plated steel for good corrosion resistance. Each clamp includes a bracket and square washer. Secure with a hex nut (sold separately).
Capacity is the maximum load for two clamps holding a pair of angles across parallel joists. The values listed are for the maximum distance between joists, which is 6 ft. For shorter distances, capacities are higher.
For technical drawings and 3-D models, click on a part number.
Washer | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Thread Size | For Angle Thick. | For Max. Beam Span, ft. | Capacity, lbs. | Mount Type | Inside Wd. | Lg. | Wd. | Ht. | Thick. | Threaded Rod Included | Material | No. Included | Each | |
Zinc-Plated Steel | ||||||||||||||
| 5/8"-11, 5/8"-18 | 3/16"-1/4" | 6 | 500 | Clamp On | 1 1/2" | 2 3/8" | 2" | 2" | 1/4" | No | Steel | 1 | 0000000 | 000000 |
Seismic Bracing Anchors and Brackets
These OSHPD approved anchors and brackets support threaded-rod-mount hangers during seismic activity. A complete seismic bracing system consists of an upper bracket, a lower bracket, and strut or pipe (sold separately). Brackets work with standard-wall (Schedule 40) pipe sizes 1-2 as well as 1 5/8" wide strut channel. Mount the upper bracket directly to a ceiling or other flat surface, or use an anchor to mount the system to angles, beams, and joists.
Angle iron anchors allow you to mount upper brackets to pairs of angles, such as those used in ceiling joists. Their set screws have heads that break off when the screw is tightened to ensure proper installation.
For Beam Thick. | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Max. Beam Thick. | Wd. | Lg. | Ht. | Material | Cap., lbs. | No. of Set Screws Included | Specifications Met | Includes | Each | |
Angle Iron Anchor | ||||||||||
| 3/8" | 3 5/16" | 3" | 2 1/2" | Steel | 1,000 | 2 | C-UL Listed FM Approved OSHPD Approved UL Listed  | 1/2" Bolt and Nut, Set Screws | 0000000 | 000000 |