Also known as screw-machine and stub-length bits, these provide maximum rigidity for drilling straighter holes than jobbers'- and maintenance-length drill bits.

These jobbers'-length bits have the rigidity and length required for most applications.

Specially-designed flutes keep these bits centered as they drill, resulting in straighter, rounder holes with tighter tolerances. Also known as double-margin drill bits.

Also known as screw-machine and stub-length bits, these provide maximum rigidity for drilling straighter holes than jobbers'-length drill bits.

Three cutting edges instead of the typical two enable these bits to drill holes with a smoother finish than other bits.

The short flutes provide increased rigidity for drilling straighter holes than standard extended-length drill bits.

Also known as screw-machine and stub-length bits, these provide maximum rigidity for drilling straighter holes than jobbers'-length drill bits.

Insert these bits directly into power screwdrivers, impact drivers, and other tools that accept 1/4" hex shanks.

Use for drilling in most metal.

Harder, stronger, and more wear resistant than cobalt steel, solid-carbide bits maintain their sharp edges longer. They require rigid toolholding to prevent breakage and should not be used in hand-held drilling applications.

Use these bits to drill a large number of holes with high precision. When the cutting edges dull, replace the carbide inserts (sold separately) instead of the entire bit.

Three drill points allow these bits to separate spot-welded panels without damaging the bottom panel.

The built-in guide has a beveled tip that fits into countersunk holes in hardware, such as hinges and latches, to center the bit.

Also known as screw-machine and stub-length bits, these provide maximum rigidity for drilling straighter holes than jobbers'- and maintenance-length drill bits.

For the highest accuracy and longest tool life, these solid-carbide bits are harder, stronger, and more wear resistant than high-speed steel, cobalt steel, and carbide-tipped bits.

More wear resistant than cobalt steel and high-speed steel, carbide-tipped bits maintain a sharper, harder edge at high temperatures for excellent performance on abrasive material, such as plastic. Because they aren’t as brittle as solid carbide bits, they can be used in less rigid setups, such as a hand-held drill.

Insert these bits directly into power screwdrivers, impact drivers, and other tools that accept 1/4" hex shanks.

Steps with progressively larger diameters let you drill a range of sizes with one bit. Also known as step drills.

Sets include cutters, a pilot pin, and a hex key. Also known as annular cutters.

Use these metric cutters with magnetic-base drills. Also known as annular cutters.

Use these cutters with Milwaukee magnetic-base drill presses. Also known as annular cutters.

Carbide is harder, stronger, and more wear resistant than cobalt steel and high-speed steel for better performance on hard and abrasive materials.

These countersinks create a surface that minimizes contact between the material and the lathe centers to prevent damage and allow for more precise machining.

Use in general purpose applications.

To remove the need for a starter hole, the drill point is incorporated into the countersink flutes.

For general purpose use.

Use on plastic and most metals.

Also known as step drill bits. The 82° countersink angle is compatible with the profile of flat- and oval-head inch screws.

Choose for general purpose applications.

Use in general purpose applications.

For excellent performance on hard and abrasive materials, carbide is harder, stronger, and more wear resistant than high-speed steel.

For use with most metals in addition to plastic and wood.

Also known as subland drill bits, these last longer than standard counterboring drill bits because the diameter stays the same after sharpening.

Drill and counterbore holes with enough clearance for socket head screws without changing tools.

These counterbores are attached to a drill bit for drilling and counterboring in a single step.

Keep counterbores in various sizes on hand to drill and counterbore holes with enough clearance for socket head cap screws without changing tools.

Available in metric sizes, these tools let you drill and ream holes with the same tool. They are for use in drill presses, turret lathes, screw machines, and other machine tools.

Enlarge existing holes without changing the depth.

Also known as gun taps, the taps in these sets have spiral-point flutes that push chips ahead of the tap and out of through holes.

Drill and tap holes in a range of diameters. With a drill bit point to drive into the workpiece, these tools can drill and tap holes in a single step. Connect them directly to drills, power screwdrivers, and other tools that accept a 1/4" hex shank.

Insert these taps directly into drills, power screwdrivers, and other tools that accept a 1/4" hex shank.

Drill and thread holes for pipe and conduit without switching tools.

The carbide teeth on these saws last up to twice as long as high-speed steel teeth.

Quickly connect these saws to your drill or drill press with the built-in arbor.

The carbide-tipped teeth on these saws last up to twice as long as high-speed steel teeth.

Make clean, fast cuts in thin metal and plastic when you use one of these saws with an impact driver. The body widens at the top to prevent the saw from pushing through your workpiece.

The carbide teeth on these steel saws cut aluminum, brass, bronze, steel, and plastic sheets and last up to twice as long as high-speed steel teeth.

Attach these saws to your portable drill to cut a range of large diameter hole sizes in sheet metal.

The saws in these kits have carbide-tipped teeth, so they last up to twice as long as saws with high-speed steel teeth.