Not only do these brass fittings have the strength to handle high-pressure applications, the male threads have a sealant applied for extra protection against leaks.

The plating on these brass fittings creates a shiny finish and provides extra protection in corrosive environments. Fittings have the strength to handle high-pressure applications.

Less than an inch in length, these miniature fittings work well in low-pressure pipe lines that are tight on space.

Used in low-pressure pipe lines, these brass fittings have a plating that makes them shiny and improves corrosion resistance.

Also known as instrumentation fittings, these have the most precise threads and the tightest tolerances of all the brass pipe fittings we offer.

Choose these fittings when you need better strength than our low-pressure brass and bronze pipe fittings.

Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings.

These brass couplings have good corrosion resistance.

Couplings can handle pressures up to 250 psi.

A single sleeve (ferrule) compresses the tubing as you tighten the nut on these fittings, creating a strong seal. They are brass for good corrosion resistance.

Also known as instrumentation fittings, these are made to tighter tolerances than standard compression fittings. They are compatible with Parker CPI fittings.

Choose these metal fittings when you need better durability than our plastic push-to-connect fittings.

Couplings allow for maximum flow because there's no shut-off valve in the plug or the socket. Compatible with Open-Flow-shape plugs and sockets.

Sockets accommodate five common plug shapes: Industrial, ARO, Lincoln, Tru-Flate, and European.

Compatible with Lincoln-shape plugs and sockets.

Metal cam-and-groove couplings have better durability than plastic cam-and-groove couplings.

Metal hose fittings have better durability than plastic barbed hose fittings.

The female connector screws directly onto the hose without the need for a separate adapter. When assembled, the fitting compresses against the hose, forming a strong seal. Also known as reusable fittings, they can be unscrewed from the hose end and used on a new hose.

Use these couplings at pressures up to 5,000 psi. They consist of a plug and socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are compatible with International Standard ISO B-shape plugs and sockets.

Attach these fittings to garden hose for a variety of water supply applications. They are metal for better durability than plastic garden hose fittings.

Couplings consist of a plug and a socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are designed for coolant applications up to 200 psi. Also known as coolant-line mold couplings.

Thread these caps and plugs onto fire hydrants and washdown equipment to close off the line. They have rocker lugs for easy gripping.

Use these couplings when you need frequent access to a gas line. A complete coupling consists of a plug and a socket that connect and disconnect quickly.

Press these grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

Kits include grommets, a cutting punch, a cutting block, an installation punch, and a die set. Use them to create a way to run rope and cable through tarps, covers, and curtains.

The sharp neck on these grommets cuts the material as you press them into place, eliminating the need for a cutting punch. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.

These extra-long plugs allow you to seal off two pipes at the same time. They have two separate inflation chambers to release back pressure gradually and prevent splash back as water clears the drain line.

Use these vents to maintain consistent pressure as temperatures fluctuate by allowing air to flow through sealed enclosures.

Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.

Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.

These grips are nickel-plated brass for good corrosion resistance.

Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.

Pair these male snap halves with female snap halves to make a complete snap.

Once installed, these fasteners provide a female snap half on one side of your fabric and a male snap half on the other.

Once installed, these fasteners provide a male snap half on both sides of your fabric. Create a complete snap by joining each male side with a female snap half for a finished look on assembled layers of fabric.

Kits include a hand punch tool with die and six complete snaps with tapping screw studs.

The drilling screw stud drills its own hole.

Create an eyelet for turn-button fastener bases.

Drive the threaded stud into a solid surface.

Minimize moisture buildup in enclosures. Also known as drain plugs, these breather vents have a small outlet that allows condensation to drain.

Easily view liquid movement and level changes from a distance—these sights have an indicator ball inside the glass window.

Press these sights into a hole in your tank wall; no additional mounting nuts are needed. They mount from the outside.

The pins on these fittings lock with dispensing tips for pin-style fittings to create a tight seal.

Access difficult-to-reach lubrication points from up to 10 ft. away.

Install these fittings into threaded holes.

Install these heaters into threaded container openings or pipe couplings to quickly and efficiently heat liquid through direct contact.

These sink drains have an overflow cutout.