We will reply to your message within an hour.
These torches handle brazing and soldering, as well as heating jobs.
Two burners with a short, wide flame concentrate heat over a large area. The tip rotates 360° to put the heat exactly where you need it.
Tackle roofing and other heavy duty heating applications—these torches have a BTU output starting at nearly seven times the output of standard propane torches.
The torch tip rotates 360° to put the heat exactly where you need it.
These torches have approximately half the BTU output of standard propane torches for use in light duty applications.
Connect these torches to a propane cylinder for light-duty flame applications.
Save time by quickly connecting and disconnecting your propane torch tips to get the right output for your job. Kits can also be used with Apachi, HPG, and propylene.
Access overhead and other hard-to-reach applications.
Get flame temperatures from these torches that are capable of cutting, welding, and brazing steel up to 3/16" thick.
Solder, desolder, and handle light brazing with these torches.
This torch includes a standard solder tip as well as a heat tip for applications that require heat without an exposed flame.
Kits include a torch, a solder tip, a heat tip, a hot knife tip, a heat-shrink attachment, a foam cutter, a wire cutter, needle-nose pliers, 60/40 tin/lead solder, a sponge, and a case.
The low profile of these torches saves bench space and the wide, heavy base adds stability.
Kits include a torch handle, tips, and a regulator.
Use these brazing alloys with a variety of metals.
No need to add flux—these alloys have it built in.
Join metal in inert atmospheres or vacuum conditions, such as furnace brazing.
To fill in large gaps, these BAg-2 alloys melt into a thicker liquid than standard brazing alloys.
When melted, these alloys form a thin liquid that easily flows into smaller gaps than standard gap-filling brazing alloys.
Use these alloys on metal subject to corrosion.
Don't worry about adding flux when brazing corrosion resistant metals such as 300-series stainless steel—these alloys have it built in.
Fill in tight gaps without needing to add flux before you braze—these alloys have flux built in. When melted, these alloys form a thin liquid that easily flows into smaller gaps than standard brazing alloys.
Create stronger bonds than standard brazing alloys.
Also known as trimetal brazing strips, these alloys have silver with nickel alloy sides and a copper core.
Join aluminum to aluminum.
Everything you need to start brazing most metals in general purpose applications.
Melting into a thick liquid, these BCuP-3 alloys fill in larger gaps than standard brazing alloys for copper.
No need to add flux when brazing aluminum parts such as radiators, power tools, and castings—these alloys don’t require it.
Join copper and copper alloys in general purpose applications.
Join copper tubing and tube fittings with these BCuP-5 alloys that create a stronger bond than standard brazing alloys for copper.
Flux is already built into these alloys, so there’s no need to add it when joining aluminum to copper.
These BCuP-5 alloys create stronger bonds than standard brazing alloys for copper.
Join aluminum to copper and copper-based alloys, such as brass and bronze.
Use this flux with silver and copper-based brazing alloys to clean and prepare surfaces.
Use this flux with silver and copper-based brazing alloys to clean and prepare surfaces. It is boron modified and residue washes off with hot water.
Since this flux doesn’t contain any fluoride, it’s environmentally friendly and safe if it gets on your hands. Use it with silver- and copper-based brazing alloys to clean and prepare surfaces.
Clean and prepare surfaces for brazing jobs that require you to join aluminum.
Clean and prepare surfaces before joining aluminum to copper. With minimal residue, this flux does not require cleanup.
Prevent the flow of flux and metal to unwanted areas during brazing.
Build a Victor torch or replace parts with our selection of handles, mixers, welding tips, cutting attachments, and cutting tips.
Create a complete Harris torch or replace parts with our selection of handles, mixers, welding tips, cutting attachments, and cutting tips.
With a needle-point flame, these kits are well-suited for use on electronics, plumbing, and small parts. They produce enough heat to weld steel up to 1/8" thick.
Weld and cut with one system. Kits include single-stage regulators, a torch with check valves to prevent the reverse flow of gas, a torch handle, a cutting attachment, a welding nozzle, a cutting tip, a torch lighter, glasses, and hose.
Weld and cut with these kits.
Create a mobile oxyacetylene welding and cutting kit.
Swap these heads out to create your own ready-to-use nozzle configuration for different welding jobs.
Electric multispark discharge means these lighters never need flints, batteries, or charging.
Ignite your gas torch with these hands-free lighters—they rest on a bench or tabletop, leaving you free to hold solder, workpieces, and other tools.
Three flints, no waiting—when one flint wears out, rotate the holder to get a fresh one.
Pull the trigger to get a spark.
Strike the flint to generate a spark.
Push the button to create a continuous flame.
Butane burns cleaner than propane at similar temperatures. Use it in heating, thawing, and soldering applications.
Produce a concentrated flame for small objects.
Heat, thaw, and sterilize in areas other burners can’t reach—these burners have a handle that lets you put flames into hard-to-reach spaces.