Pair these male snap halves with female snap halves to make a complete snap.

Kits include a hand punch tool with die and six complete snaps.

Once installed, these fasteners provide a male snap half on both sides of your fabric. Create a complete snap by joining each male side with a female snap half for a finished look on assembled layers of fabric.

Pair with a female snap half to create a complete snap.

The threaded stud installs in threaded holes.

Fasten these male snap halves to a solid surface when you only have access to one side. A blind rivet tool is required for installation.

Create an eyelet for turn-button fastener bases.

Drive the threaded stud into a solid surface.

Access to both sides of the material is required for installation.

Also known as slam rivets, the two heads provide a finished look on both sides of your material.

The washer creates a large holding surface on the back of the material. Also known as belt rivets, these are used for fastening conveyor belts or leather. A special setting tool and a hammer are required for installation.

Snap these nuts into square holes in thin materials.

Create fast connections with items, such as rope, chain, and straps.

Squeeze the trigger to quickly release the latch.

For a more secure connection than standard trigger-locking snaps, squeeze the trigger and slide the latch grip down to release.

Lock the bolt with wire or a cable tie for a secure connection.

Lock by screwing the latch into the body.

A lock slides upward over the latch to lock. The latch opens outward to accept large diameters of rope.

The narrow end restricts the movement of rope and chain, and the wide end allows room to attach multiple connectors.

Flat sides allow webbing and strapping to lay flat, so they won't slide and bunch.

Best for attaching different widths of webbing and strapping, the flat sides ensure they lay flat and won't bunch or slide.

Attach a rope to the ring on the pin for remote release where access in limited. These shackles have an eye end for connecting to a hook.

For extra security, these have a latch that snaps back into place to secure your load.

Made of steel, these are our most durable plugs for panels. Tapered prongs snap into the hole to securely hold them in place.

Vents in the top allow air circulation and permit heat and fumes to escape. These plugs have tapered prongs that snap into the hole to securely hold them in place.

Vents in the top allow air circulation and permit heat and fumes to escape. All of these plugs have wings that expand against the sides of the hole to lock them in place.

The wings on these plugs expand against the sides of a hole to form a liquid-tight seal. Pierce the plugs with round wire, cable, or tubing and they function as a grommet to create insulated holes.

Flexible ridges or straps hold these plugs in place.

Flexible ridges securely hold these plugs in place and allow them to fit a range of hole sizes.

A one-piece hinged design allows frequent access to screw heads without misplacing the top. To conceal and protect the entire screw head, insert your screw through the hole in the base and flip the hinged top over.

Snap these caps into flange bolt holes to safeguard pipe flanges during shipping, storing, and finishing applications. They all have a thick center pad to protect the flange opening and pipe threads from damage.

Squeeze the adjustable handle to install standard and dual-sided fabric snaps and fabric grommets.

Slide these tools under the head of push-in rivets and squeeze the handles to pop the rivet out. They are also known as panel clip pliers.

With D-rings on the shoulders, these harnesses allow you to raise and lower workers.

These harnesses have leather-insulated metal components and meet ASTM F887 when used with an arc flash-resistant lanyard.

D-rings on each hip provide a stable working position.

Made of Kevlar, these lanyards meet ASTM F887 when used with an arc flash-resistant harness.

Made of steel, these durable lanyards hold up in abrasive and high-heat applications.

A quick-stop lanyard must be used when you have less than 18 1/2 ft. of fall clearance as it will stop your fall within a few inches.

The center hole has flaps that flex to hold and protect various sizes of wire, cable, and cords while keeping out dust and debris. Snap these grommets into place and their wings expand against the sides of the hole to lock them in position. Use them to turn rough-edged and uneven holes into smooth holes.

No setting tools needed—snap the two parts together in a hole you've already cut to strengthen the hole and eliminate fraying. Use these grommets in tarps, covers, curtains, and other material.

These grommets have two flanges that snap around holes and flex to compensate for misalignment and movement of pipe and tubing. They're often used for routing applications in panel walls.

Mushroom-shaped heads interlock for a secure hold when two pieces are pressed together.

Fasteners are cut into convenient rectangles and discs.