Protect screw-together M12 connectors when not in use.

Send power and signal to devices with M12 connections that are exposed to some of the toughest industrial stresses—from welding to metal machining and changing temperatures.

Quickly mate these connectors by pushing them together. They're often used with 12 mm proximity switches and valves in automated systems.

Safely use these connectors with 12 mm proximity switches, console lights, valves, and power supplies in food, beverage, and pharmaceutical applications—they’re FDA compliant for direct food contact.

Plug these connectors into hazardous location devices. Using a NAMUR signal, they operate at a low current and voltage, so they prevent the risk of sparks and ignition in volatile areas.

Protect mini connectors when not in use.

Send higher current than M5, M8, and M12 connectors near tough industrial jobs, such as welding and metal machining.

Protect harsh environment mini connectors when not in use.

Send higher current than M12 connectors to automated systems, motors, and pumps in environments where washdowns are common.

Also known as dummy plugs, these plugs close the electrical circuit on your mini connector, so you can safely change devices or repair connections.

Also known as pico connectors, these connectors are often used with 8 mm and smaller proximity switches and photoelectric switches.

Connect different pole configurations to join sensors, switches, and other devices to cords, distribution blocks, and I/O modules.

A TPE cable protects these connectors from oil, weld slag, and other tough industrial stresses as they send signal and power to low-current devices with M8 connections.

Visually check that your low-current devices with M8 connections are powered up and sending and receiving signals. These connectors illuminate green if they have power and yellow if they have signal.

Rated IP69K, these M16 connectors protect against dust, debris, and hot, high-pressure jets of water at high volumes.

Join two devices with M8 connectors to a single cord, distribution block, or I/O module with M12 connectors to save space and reduce the number of cords in industrial automation setups. Often used with sensors and switches, these splitters send or receive two signals through one connection.

Join M8 connections to M12 connections.

Rated to MIL-DTL-5015 specifications, these connectors are compatible with other products that meet the same standard. They screw together for a secure connection.

These connectors meet MIL-DTL-26482, so they're compatible with other products that meet the same standard. Quickly mate by pushing them together.

Make secure connections with machine tools, robots, and other equipment that vibrates frequently and carries currents as high as 300 amps.

Choose a socket that works with your Siemens servomotor system.

Often used in devices that branch off of the main power line, these connectors power high-amperage fans, pumps, and machines in motor controls, conveyors, and sorting and packaging systems.

With thick threads similar to a light bulb, these connectors take only a few turns to lock into place for a secure connection in washdown and high-vibration areas. Detach them just as quickly for frequent maintenance.

Power hydraulic and air-powered valves, motors, pumps, and pressure switches.

Caps are watertight to protect hazardous location safe-break plugs when not in use.

Caps are watertight to protect safe-break plugs when not in use.

Protect high-current connectors when not in use.

These panel-mount adapters have a female USB connection on both ends to join two USB cables.

Connect two DisplayPort cords of the same gender and connection type.

Mount these adapters directly into panel cutouts to attach D-Sub connectors and cords to computers.

Use these connectors and cords to make Ethernet connections in wet location environments.

Audio/video HDMI connectors and cords are rated IP67 when mated.

Install these connectors in a panel cutout to create a port for transferring data.

Transmit audio, video, and data through coaxial cable.

Use these unshielded cords where signal interference is not a concern.

Attach these caps to the socket end of washdown USB cords to maintain an IP67 rating when cords are not in use.

The threaded ends on these cords seal out contaminants and resist coming loose from vibration in tough industrial environments and automated systems while sending power and signal to devices with M12 connections.

Step on or roll carts and platform trucks over these M12 cords without crushing them.

TPE insulation protects these cords from some of the toughest industrial conditions, including abrasion, coolants, chemicals, UV rays, and weld slag. Use them in areas with welding, machining, and fluctuating temperatures to send signal and power to M12 proximity switches, valves, and other devices.

Connect two devices to a distribution block or I/O module with just one cord. Often used with sensors and actuators, these splitters send power/signals to your devices through a single connection.

Often used for automated systems, motors, and pumps in tough industrial areas such as near welding and metal machining, these cords carry higher current than M5, M8, and M12 cords.

With a higher maximum current than nano M8 and micro M12 cords, these mini cords are often used with automated systems, motors, and pumps.

Use these cords with hydraulic and air-powered valves, motors, pumps, and pressure switches. They have a solenoid valve socket on one end and an M12 threaded plug on the other.

Like a tree trunk connecting to branches, these cords supply power to a chain of devices. Send power to high-amperage motors, robotic arms, and other machines in motor controls, conveyors, and sorting and packaging systems.

Similar to branches extending from a tree, these cords disperse power from a main power line to run a chain of devices. Power high-amperage fans, pumps, and other machines in motor controls, conveyors, and sorting and packaging systems.

A 316 stainless steel body gives these fittings the best corrosion resistance of all our metal push-to-connect tube fittings.

Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings.

Use at pressures up to 250 psi.

Withstanding temperatures up to 300° F, these fittings have the highest temperature rating of all our push-to-connect tube fittings for air and water.

Aluminum fittings have good corrosion resistance, but are lighter in weight than brass.

You don't need a clamp to secure these fittings to tubing. They have a nut on the barbed end that tightens to holds the tubing in place.

Lighter in weight than metal quick-disconnect couplings, these couplings are plastic.

With no latch, these couplings have a compact design to fit in small spaces. They can handle pressures up to 700 psi.

Made of acetal, these compression fittings are lighter in weight than metal compression fittings and won’t absorb moisture when used in wet environments.

These fittings keep their strength in moist environments and meet NSF/ANSI 61 for drinking water. Also known as instant fittings.

Quick-disconnect couplings consist of a plug and a socket that join with a latch so you can easily connect and disconnect your line. Use in applications up to 150 psi.

Also known as instant fittings, these chemical-resistant plastic fittings connect to tubing with a push, and an internal gripping ring and fluoroelastomer O-ring hold the tubing tight.

These plastic compression fittings meet NSF/ANSI Standard 51 for food contact.

These quick-disconnect couplings meet NSF/ANSI 169 for food equipment.

For applications that require an extra level of cleanliness, these fittings are individually bagged to prevent contamination.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

A PTFE seal on the tube end of these fittings allows for an extra-strong connection in high-vibration applications.

Transfer liquids and gasses into high-vacuum chambers with these assembled fittings, also known as feedthroughs.

Also known as JIC (Joint Industrial Council) fittings, these connect to tubing that is flared to 37°. They can handle higher pressures than 45° flared fittings.

These fittings have two sleeves for extra gripping power. They bite into steel tubing as you tighten the nut to form a strong seal.

The plating on these brass fittings creates a shiny finish and provides extra protection in corrosive environments. Fittings have the strength to handle high-pressure applications.

In addition to being lightweight, these aluminum fittings offer good corrosion resistance. Use them in low-pressure flow applications.

These fittings are strong enough to handle extreme pressures, yet small enough to fit into cramped spaces.

Connect these fittings to Schedule 40 plastic pipe—they are the industry standard for residential and commercial low-pressure plumbing and water supply applications. They are plastic for good corrosion resistance.

Made of corrosion-resistant plastic, these fittings won’t deteriorate when used in oil applications. They have high strength and impact resistance.

Extreme temperatures are no problem for these fittings—they’re made of PTFE, so they can withstand a wider temperature range than any of our other plastic pipe fittings for chemicals. They are commonly used in high-purity chemical flow processes, such as semiconductor and clean room applications.

A splined core limits contact points on the cable’s liner, so the core slides back and forth smoothly and keeps the cable from twisting. Pair these cables with a knob or lever to operate valves, throttle controls, and HVAC damper controls from a distance. They're flexible for weaving around obstructions.

Similar to the brake cable on a bicycle, these cables exert pulling force so you can control components such as latches, release valves, and brakes.