Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

With a flexible layer of rubber sandwiched between an oil-embedded bronze bearing and rigid metal shell, these bearings reduce wear and machinery noise.

A metal shell adds strength.

Made of FDA-listed materials or FDA compliant, these bearings are for use in food applications. They also withstand caustic and washdown environments.

These bearings stand up to a wider range of chemicals than other dry-running sleeve bearings.

Good for underwater applications, these bearings won’t swell or warp when wet.

A figure-8-shaped groove provides a flow path for lubricant, distributing it evenly along the bearing’s surface.

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

The oil in these bearings is suitable for incidental contact with food.

These bearings come with a traceable lot number and material test report. They are also known as Oilite® bearings.

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.

An aluminum shell adds strength.

Good for underwater applications, these bearings won’t swell or warp when wet.

The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

Use where high loads and speeds are not required.

Good for underwater applications, these bearings won’t swell or warp when wet.

The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

Capable of handling temperatures from -400° to 750° F, these graphalloy bearings withstand the widest temperature range of any of our mounted bearings.

A strong steel housing allows these bearings to handle higher speeds than standard oil-embedded mounted sleeve bearings.

A reliable classic—these babbitt bearings are strong and corrosion resistant.

Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface.

Precisely shaped to fit snugly on keyed shafts, these shims align, level, and space components. Because of their tight fit, they also help components rotate in unison with the shaft.

Be prepared with shims in a variety of thicknesses. These shims are shaped to fit over D-profile shafts. Use them to precisely align, level, and adjust spacing.

The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings.

Also known as Trantorque bushings, these tighten with a twist of the collar nut—no screws needed.

Insert these bushings into the bore of your sprocket for flush or recessed mounting.

Made of chemical-resistant nylon, these collars are suitable for washdown applications.

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.

Installing and removing a collar is as easy as pushing down and lifting up a clamp lever.

An embedded sleeve squeezes the shaft as you tighten the clamping screws, allowing these collars to handle up to three times the thrust load of standard collars.

Wider than standard shaft collars with twice the number of clamping screws, these ensure a better grip for greater holding power.

One side of these collars locks down like a standard one-piece shaft collar; the other has a flush face that's flat to 0.0005", which lets you mount the collars on a shaft next to precision bearings, sprockets, and gears.

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.

Wider than standard shaft collars with twice the number of clamping screws, these ensure a better grip for greater holding power.

Make quick adjustments to these shaft collars with a lever on the side.

Tighten the set screw to bite into an unhardened shaft for a secure hold.

Two tapped holes on the face of these collars allow you to fasten them to gears, pulleys, and sprockets.

Install these collars anywhere on a shaft without removing components or having access to the ends of the shaft.

Secure items to either side of these collars—each half has a flat end with a tapped hole

Slide these one-piece collars onto the end of your shaft to create an end-stop for linear components.

When one of your shafts is undersized from wear, oversized from coatings, or uncommonly sized, machine one end of these couplings to fit. They clamp around your shafts for a secure hold that won’t cause damage.

These couplings have the gripping strength to handle higher torque than most other couplings.

These couplings have the gripping strength to handle higher torque than most other couplings.

Support the weight of a motor and transfer torque to another shaft at the same time with these couplings.

Each hub includes a set screw (unless noted), which bites into your shaft to hold the coupling in place.

Safely connect slightly misaligned shafts near food lines—the spider on these couplings contains metal, so it’ll trigger a metal detector if a piece frays off and contaminates your batch.

Reduce the diameter of your shaft while adding length.

Ridges on the inside of these bearings wipe away dust and debris as the bearing travels on a shaft.

Use ball bearings in debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

The choice for low-friction motion in high-temperature environments.

Ball bearings create less friction than sleeve bearings, so they require less force to operate.