Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

The oil in these bearings is suitable for incidental contact with food.

These bearings come with a traceable lot number and material test report. They are also known as Oilite® bearings.

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

A slit running along the length of these bearings allows you to quickly slip them into a housing—no tools required.

An aluminum shell adds strength.

Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings.

The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

With a flexible layer of rubber sandwiched between an oil-embedded bronze bearing and rigid metal shell, these bearings reduce wear and machinery noise.

The oil in these bearings is suitable for incidental contact with food.

Graphite provides a layer of dry lubrication that can operate in high-temperature environments.

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

These bearings stand up to a wider range of chemicals than other dry-running sleeve bearings.

Good for underwater applications, these bearings won’t swell or warp when wet.

A figure-8-shaped groove provides a flow path for lubricant, distributing it evenly along the bearing’s surface.

Grooves on the inside of the bearing provide a flow path for lubricant, distributing it evenly along the bearing’s surface.

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

The oil in these bearings is suitable for incidental contact with food.

Use where high loads and speeds are not required.

Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.

Good for underwater applications, these bearings won’t swell or warp when wet.

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

Use these UHMW bearings in wet, corrosive environments.

Made of acetal blended with PTFE, these bearings handle speeds twice as fast as standard sleeve bearings.

With a flexible layer of neoprene sandwiched between an oil-embedded bronze bearing and rigid steel shell, these bearings reduce wear and machinery noise.

A reliable classic—these babbitt bearings are strong and corrosion resistant.

Use these nylon or acetal bearings for light loads. The closed backing blocks out dust and other contaminants.

Handling speeds twice as fast as standard mounted sleeve bearings while limiting wear on your system, these bearings are made of PTFE-filled acetal.

Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface.

Precisely shaped to fit snugly on keyed shafts, these shims align, level, and space components. Because of their tight fit, they also help components rotate in unison with the shaft.

Be prepared with shims in a variety of thicknesses. These shims are shaped to fit over D-profile shafts. Use them to precisely align, level, and adjust spacing.

Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws.

Also known as Trantorque bushings, these tighten with a twist of the collar nut—no screws needed.

Insert these bushings into the bore of your sprocket for flush or recessed mounting.

Reduce the ID of sprockets, pulleys, and gears in low-torque applications.

Made of chemical-resistant nylon, these collars are suitable for washdown applications.

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.

Installing and removing a collar is as easy as pushing down and lifting up a clamp lever.

A threaded lever lets you tighten these collars with more torque than other quick-release styles, ensuring that they stay put on your shaft.

Two knurled sides provide micrometer-like movement for precise width adjustments.

One side of these collars locks down like a standard one-piece shaft collar; the other has a flush face that's flat to 0.0005", which lets you mount the collars on a shaft next to precision bearings, sprockets, and gears.

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.

Use a wrench to rotate your drive shaft without marring or gouging the shaft.

Although these collars fit inch-sized shafts, they have a metric OD and width for use with metric equipment.

Two tapped holes on the face of these collars allow you to fasten them to gears, pulleys, and sprockets.

Install these collars anywhere on a shaft without removing components or having access to the ends of the shaft.

Secure items to either side of these collars—each half has a flat end with a tapped hole

Slide these one-piece collars onto the end of your shaft to create an end-stop for linear components.

Install these collars anywhere on a shaft without removing components or having access to the ends of the shaft.

One end has a finished bore size; the other can be machined to any size—great for connecting to uncommon shaft sizes and shafts that are undersized from wear or oversized from coatings.

These couplings have the gripping strength to handle higher torque than most other couplings.

These couplings have the gripping strength to handle higher torque than most other couplings.

Each hub includes a set screw (unless noted), which bites into your shaft to hold the coupling in place.

Designed for use in food-processing applications, where a fraying spider could contaminate a batch, these couplings have a metal-detectable rubber spider. Small pieces of metal inside the rubber will set off a metal detector, alerting you to the problem.

Designed to grip evenly around your shaft, these couplings provide more holding power than set screw couplings without marring the shaft.

An acetal plastic spacer at the center of these couplings insulates bearings, encoders, and other shaft components from stray electric current. Use them with servomotors, which sometimes generate current that travels down the shaft and can damage circuit boards, interfere with readings, and cause wear on bearing raceways.

Reduce the diameter of your shaft while adding length.

Ridges on the inside of these bearings wipe away dust and debris as the bearing travels on a shaft.

Made of FDA-listed materials for use in food applications, these bearings also have excellent chemical and corrosion resistance.

Use ball bearings in debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

The choice for low-friction motion in high-temperature environments.

Sleeve bearings outperform ball bearings in dirty environments. Use them for low speed applications.

Ball bearings create less friction than sleeve bearings, so they require less force to operate.

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard linear ball bearings for support rail shafts.

The shell, housing, and balls of these bearings are stainless steel for excellent corrosion resistance.

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

Choose ball bearings for debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

Use the adjustment screw in the housing to tighten or loosen the snugness (also known as preload) of the bearing to your shaft.

Float bearings on air for precise, frictionless movement. Unlike traditional bearings that can wear your shaft down, these bearings are suspended using pressurized air for linear and rotary motion.