Use where high loads and speeds are not required.

Acetal bearings have low moisture absorption and are more chemical resistant than nylon and MDS-filled nylon bearings.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

PTFE bearings have good chemical resistance.

Rulon J bearings create the least amount of friction of any bearing that we offer. They handle heavier loads than PTFE bearings.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Use where high loads and speeds are not required.

Thermoplastic bearings are fiber reinforced and lubricant infused for good wear resistance and low friction with light and medium loads.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Keep these shaft collars in place by tightening their set screw into the shaft. The tip of the screw digs in for a secure hold, but will mar the shaft’s surface. For maximum holding power, make sure the set screw material is harder than your shaft material. Use these shaft collars to position and retain power transmission components such as sprockets, pulleys, and bearings. You can also use them to limit the movement of a shaft.

Carbon steel collars are strong and wear resistant. Collars with a black-oxide finish have some corrosion resistance, but only in dry environments. Their dark color can be useful for matching other parts in your system. Collars that are blue make it easy to identify metric collars at a glance. They’re tinted to match other blue metric fasteners.

303 stainless steel collars are corrosion resistant and highly machinable.

DIN 705 collars meet an international standard for shaft collar dimensions.

For technical drawings and 3-D models, click on a part number.

These metal collars are stronger than plastic shaft collars. They clamp evenly around the shaft to create a strong, mar-free hold. To use, slide onto your shaft and tighten the clamping screw to secure.

Black-oxide steel collars have some corrosion resistance. Zinc-plated steel collars have moderate corrosion resistance. Aluminum collars are lightweight and have good corrosion resistance. Anodized aluminum collars are lightweight like unfinished aluminum collars, but they’re more corrosion resistant and have better screw seating torque, which means they’re less likely to shift. 303 stainless steel collars have excellent corrosion resistance. 316 stainless steel collars have excellent corrosion and chemical resistance.

For technical drawings and 3-D models, click on a part number.

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance. They clamp evenly around the shaft to create a strong, mar-free hold. To use, slide onto your shaft and tighten the clamping screw to secure.

Acetal collars have a naturally slippery surface and resist swelling when exposed to moisture.

For technical drawings and 3-D models, click on a part number.

These metal collars are stronger than plastic shaft collars. The two-piece design allows you to install them anywhere on a shaft without removing components or having access to the ends of the shaft. Collars clamp evenly around the shaft to create a strong, mar-free hold. Tighten the clamping screws to secure.

Black-oxide steel collars have some corrosion resistance. Zinc-plated steel and chrome-plated steel collars have moderate corrosion resistance with a bright finish. Aluminum collars are lightweight and have good corrosion resistance. In addition to the benefits of aluminum, anodized aluminum collars have extra corrosion resistance, and you can tighten the clamping screw with more torque, so they stay in place. 303 stainless steel collars have excellent corrosion resistance. 316 stainless steel collars have excellent corrosion and chemical resistance.

For technical drawings and 3-D models, click on a part number.

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance. The two-piece design allows you to install them anywhere on a shaft without removing components or having access to the ends of the shaft. Collars clamp evenly around the shaft to create a strong, mar-free hold. Tighten the clamping screws to secure.

Acetal collars have a naturally slippery surface and resist swelling when exposed to moisture.

For technical drawings and 3-D models, click on a part number.