A plastic cover fully insulates these splices.

Crimp the barrel twice on each end for an extra-tight grip in high-vibration applications. A plastic cover fully insulates these splices.

When heat is applied, adhesive-lined insulation shrinks and bonds to wires, creating a moisture- and corrosion-resistant seal.

Visually confirm your connection through the inspection window.

When heat is applied, adhesive-lined insulation shrinks and bonds to the wires, creating a watertight seal.

Check to make sure you’ve made a secure connection between two different sizes of wire with the inspection window on these splices. When heated, their adhesive-lined insulation shrinks and bonds to wires, creating a water- and corrosion-resistant seal.

For use with a compression tool, these splices are color-coded to match compression dies.

Compress the barrel twice on each end for an extra-tight grip in high-vibration applications.

Insert wires and twist on the threaded end caps. The caps lock wires into place, making these splices a good choice for high-vibration applications.

Press down on the clamp to connect wires for quick field installation, no crimping or tools required

With a ring of solder on the inside, these heat-shrink splices create secure, water-resistant connections between wires without the need for a crimping tool.

Tighten the screws to connect wires.

Make watertight connections for underground applications.

Pierce the insulation of wire without stripping it to make quick connections that are also sealed to keep out water.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

Also known as I-line fittings, these fittings have a male adapter that interlocks with a female adapter for more support than standard quick-clamp fittings.

Also known as KF, QF, and NW fittings, these fittings are for high-vacuum applications, such as vacuum coating and heat treating, leak testing, and analyzing gases.

Polished to at least a 15 Ra finish on the inside, these fittings have an ultra-smooth interior surface that helps prevent contamination. They are also known as ultra-high-purity fittings.

Fittings are polished to a32 Ra and under finish on the interior.

Create access points in ultra-high-vacuum lines or chambers by bolting two same-size flanges together with a copper gasket between them. The flanges’ sharp edges dig into the copper gasket and form an extremely tight seal, which means they handle higher vacuum pressures than other high-vacuum fittings with rubber gaskets.

Use these corrosion-resistant fittings in a low-pressure pipe line.

Unlike other stainless steel fittings, these are made in the U.S.A. for superior quality. As another marker of quality, they come with a certificate with a traceable lot number and test report that guarantees material composition.

Use these heavy duty, corrosion-resistant fittings in high-pressure flow applications.

Bolt two same-size flanges together with a gasket to create an access point within a pipe line.

Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slip the pipe into the socket and weld.

Use these heavy duty forged flanges for high-pressure applications.

Also known as Schedule 10 fittings, these are thin, lightweight, and corrosion resistant.

Also known as Schedule 40, this steel pipe is designed for low-pressure applications.

Typically used with extreme-pressure iron and steel threaded pipe fittings. Also known as Schedule XXH.

A galvanized finish gives these fittings better corrosion resistance than our plain steel high-pressure fittings. Also known as Pressure Class 3000 fittings.

Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slide the pipe into the socket and weld.

Typically used with thick-wall and high-pressure iron and steel unthreaded pipe fittings. Also known as Schedule 80.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

Typically used with standard-wall and low-pressure iron and steel unthreaded pipe fittings. Also known as Schedule 40.

Typically used with extreme-pressure iron and steel unthreaded pipe fittings. Pipe is also known as Schedule XXH .

In addition to being lightweight, these aluminum fittings offer good corrosion resistance. Use them in low-pressure flow applications.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

Also known as Schedule 40 fittings, these have thicker walls than our thin-wall aluminum unthreaded pipe fittings.

Use these unthreaded flanges in low-pressure applications. Also known as Pressure Class 125 flanges.

Also known as Pressure Class 200 fittings.