Component Component |
|---|
|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
Material Material |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
For Maximum Push-Button Projection For Maximum Push-Button Projection |
|---|
|
|
For Maximum Rocker Cutout Height For MaximumRocker Cutout Height |
|---|
|
|
|
Mounting Location Mounting Location |
|---|
|
Choosing an Electrical Switch
More
Two-Hand Safety Switches
It takes two hands to activate these switches, minimizing the risk of accidental equipment start up. A complete system requires two switches, one safety relay, and two outlet boxes.
Switches meet OSHA requirements and ANSI standards for machine operator safety. They're rated IP64 for protection from splashing water.
Safety relays control the two switches by sending an output signal when both switches are activated within 0.5 seconds of each other. Self-monitoring circuitry offers additional protection—if any part of the system fails, the entire system shuts down until repaired.
Outlet boxes have a drilled hole to fit the switch.
Switch guards protect switches against damage and accidental activation. Use one guard per switch.
For technical drawings and 3-D models, click on a part number.
Actuator | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Input Voltage | No. of Circuits Controlled | Switch Starting Position | Switch Action | No. of Terminals | Industry Designation | Material | Color | Switching Current @ Voltage | Dia. | Each | |
| 24V DC | 2 | 1 Off (Normally Open) and 1 On (Normally Closed) | Springs Back (Momentary) | 4 | DPST-1NO/1NC | Plastic | Gray | 1 A @ 250 V AC/90 V DC | 2 3/8" | 00000000 | 0000000 |
| 120V AC | 2 | 1 Off (Normally Open) and 1 On (Normally Closed) | Springs Back (Momentary) | 4 | DPST-1NO/1NC | Plastic | Gray | 1 A @ 250 V AC/90 V DC | 2 3/8" | 00000000 | 000000 |
| Input Voltage | No. of Circuits Controlled | Switch Starting Position | No. of Terminals | Industry Designation | Switching Current @ Voltage | For DIN Rail Ht., mm | Wire Connection Type | Each | |
| 24V AC/24V DC | 2 | 2 Off (Normally Open) | 4 | DPST-NO | 4 A @ 230 V AC, 2 A @ 24 V DC | 35 | Screw Terminals | 00000000 | 0000000 |
| 115V AC | 2 | 2 Off (Normally Open) | 4 | DPST-NO | 4 A @ 230 V AC, 2 A @ 24 V DC | 35 | Screw Terminals | 00000000 | 000000 |
Conduit | ||||||||
|---|---|---|---|---|---|---|---|---|
| No. of Connections | Trade Size | Ht. | Wd. | Dp. | Mounting Fasteners Included | Environmental Rating | Each | |
| 1 | 3/4 | 2 1/8" | 2 7/8" | 6" | Yes | IP64 | 00000000 | 0000000 |
| Ht. | Wd. | Dp. | Each | |
| 2" | 4 7/8" | 5 3/8" | 00000000 | 0000000 |
Guards for Toggle Switches
Keep two-position toggle switches safely locked in the off position. These spring-loaded guards will stay up when opened, but return the toggle to the off position when closed.
For technical drawings and 3-D models, click on a part number.
| For Mounting Thread Size | For Max. Toggle Dp. | For Panel Cutout Dia. | Features | Each | |
| 15/32"-32, M12 | 0.69" | 1/2" | Spring-Loaded Cover | 000000 | 000000 |
Covers for Toggle Switches
Protect toggle switches from moisture and dust by replacing panel mounting nuts with these rubber covers.
For technical drawings and 3-D models, click on a part number.
For Max. Toggle | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Mounting Thread Size | Mounting Thread Pitch | Dp. | Dia. | Includes | Environment | Environmental Rating | Specifications Met | Choose a Color | Each | |
| 1/4"-40 | __ | 0.37" | 0.06" | Mounting Nut | Corrosive, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 0000000 | 00000 | |
| 1/4"-40 | __ | 0.5" | 0.06" | Mounting Nut | Corrosive, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 0000000 | 0000 | |
| 15/32"-32 | __ | 0.71" | 0.22" | Mounting Nut | Corrosive, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 0000000 | 0000 | |
| 15/32"-32 | __ | 0.9" | 0.22" | Mounting Nut | Corrosive, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 00000000 | 0000 | |
| 15/32"-32 | __ | 0.92" | 0.3" | Mounting Nut | Corrosive, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 00000000 | 0000 | |
| 1/2"-32 | __ | 0.66" | 0.22" | Mounting Nut | Corrosive, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 00000000 | 0000 | |
| M12 | 1 mm | 0.67" | 0.23" | Mounting Nut | Corrosive, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | Black | 00000000 | 0000 |
Panel Seals for Toggle Switches
Seal the panel cutout around a toggle switch. Use these seals in place of panel mounting nuts to protect toggle switches against moisture and dust.
For technical drawings and 3-D models, click on a part number.
| Mounting Thread Size | For Max. Toggle Dia. | Material | Includes | Specifications Met | Color | Each | |
| 15/32"-32 | 0.47" | Rubber | Mounting Nut | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | Gray | 00000000 | 00000 |
Seals for Toggle Switches
Create a seal around the base of a toggle to protect against moisture and dust while leaving the actuator exposed. To install, replace the panel mounting nuts with these seals.
For technical drawings and 3-D models, click on a part number.
| Mounting Thread Size | For Max. Toggle Dia. | Material | Includes | Environment | Environmental Rating | Specifications Met | Choose a Color | Each | |
| 1/4"-40 | 0.19" | Rubber | Mounting Nut | Corrosive, Oily, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 0000000 | 00000 | |
| 15/32"-32 | 0.21" | Rubber | Mounting Nut | Corrosive, Oily, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | Gray | 00000000 | 00000 |
| 15/32"-32 | 0.24" | Rubber | Mounting Nut | Corrosive, Oily, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 0000000 | 0000 |
Quick-Install Covers for Toggle Switches
Install these covers without removing switches from the panel—covers fit over mounting hardware. They protect toggle switches from moisture and dust.
For technical drawings and 3-D models, click on a part number.
Heavy Duty Covers for Toggle Switches
With a nickel-plated brass cap, these covers are more impact resistant than rubber covers. Use them in place of panel mounting nuts to protect toggle switches from moisture and dust.
For technical drawings and 3-D models, click on a part number.
For Max. Toggle | |||||||
|---|---|---|---|---|---|---|---|
| Mounting Thread Size | Dp. | Dia. | Includes | Environmental Rating | Specifications Met | Each | |
| 15/32"-32 | 0.66" | 0.22" | Mounting Nut | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 0000000 | 000000 |
Covers for Push-Button Switches
Protect switches from moisture and dust by replacing panel mounting nuts with these rubber covers.
For technical drawings and 3-D models, click on a part number.
Mounting Thread | For Max. Push-Button | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Size | Type | Dia. | Projection | Material | Includes | Environment | Environmental Rating | Specifications Met | Choose a Color | Each | |
| 1/4"-40 | UNS | 0.19" | 0.2" | Rubber | Mounting Nut | Corrosive, Oily, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 00000000 | 00000 | |
| 1/4"-40 | UNS | 0.19" | 0.26" | Rubber | Mounting Nut | __ | __ | __ | 0000000 | 0000 | |
| 3/8"-27 | UNS | 0.3" | 0.4" | Rubber | Mounting Nut | Corrosive, Oily, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 00000000 | 0000 | |
| 3/8"-32 | UNEF | 0.3" | 0.42" | Rubber | Mounting Nut | Corrosive, Oily, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 00000000 | 0000 | |
| 15/32"-32 | UNS | 0.42" | 0.28" | Rubber | Mounting Nut | Corrosive, Oily, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 00000000 | 0000 | |
| 15/32"-32 | UNS | 0.42" | 0.44" | Rubber | Mounting Nut | Corrosive, Oily, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 00000000 | 0000 | |
| 1/2"-32 | UNS | 0.42" | 0.28" | Rubber | Mounting Nut | Corrosive, Oily, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 00000000 | 0000 | |
| 5/8"-24 | UNEF | 0.52" | 0.28" | Rubber | Mounting Nut | Corrosive, Oily, Outdoor, Submersible, Washdown | IP66, IP68, NEMA 6P, NEMA 13 | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 00000000 | 0000 | |
Heavy Duty Covers for Push-Button Switches
Made of stainless steel, these covers offer more protection than rubber covers. Use them in place of panel mounting nuts to protect push-button switches from impact, moisture, and dust.
For technical drawings and 3-D models, click on a part number.
Mounting Thread | For Max. Push-Button | |||||||
|---|---|---|---|---|---|---|---|---|
| Size | Type | Dia. | Projection | Material | Includes | Specifications Met | Each | |
| 15/32"-32 | UNS | 0.42" | 0.3" | Stainless Steel | Mounting Nut | A-A-59588 Class 3A Grade 50, C-UL Recognized Component, UL Recognized Component | 00000000 | 000000 |
Covers for Rocker Switches
With extended flaps to shield the entire switch, these covers protect rocker switches from moisture and dust.
For technical drawings and 3-D models, click on a part number.
For Max. Switch | For Max. Rocker Cutout | |||||||
|---|---|---|---|---|---|---|---|---|
| Ht. | Wd. | Ht. | Wd. | Environment | Environmental Rating | Material | Each | |
| 0.83" | 0.59" | 0.75" | 0.5" | Wet Location | IP54 | Rubber | 0000000 | 00000 |
| 0.86" | 0.39" | 0.75" | 0.28" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 0.96" | 0.96" | 0.88" | 0.75" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 0.96" | 1.04" | 0.75" | 0.75" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.09" | 0.73" | 0.95" | 0.61" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.22" | 1" | 1.13" | 0.88" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.22" | 1" | 1.17" | 0.81" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.22" | 1" | 1.18" | 0.87" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.22" | 1" | 1.19" | 0.81" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.22" | 1" | 1.19" | 0.88" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.22" | 1" | 1.2" | 0.87" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.27" | 0.68" | 1.12" | 0.48" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.27" | 0.68" | 1.13" | 0.48" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.27" | 0.68" | 1.15" | 0.48" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.72" | 0.97" | 1.25" | 0.75" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.72" | 0.97" | 1.34" | 0.69" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 1.72" | 0.97" | 1.5" | 0.88" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
| 2.19" | 0.98" | 1.44" | 0.94" | Wet Location | IP54 | Rubber | 0000000 | 0000 |
Film with Copper Ion Finish
Keep frequently touched elevator panels, kiosks, counters, and other large surfaces free of germs. This film has a copper ion finish on the coarse side that stops microbes such as bacteria, mold, mildew, and fungi from growing. It's semi-clear, so it won’t obscure details of the surface below. Do not clean the film with detergents or disinfectants. Replace it after six months of use or if it becomes damaged or worn.
| Length | Width | Thickness | Texture | Color | Clarity | Each | |
Polyethylene Plastic | |||||||
|---|---|---|---|---|---|---|---|
Sheet | |||||||
| 48" | 12" | 0.006" | Coarse | Brown | Semi-Clear | 0000000 | 000000 |
Button Covers with Silver Ion Finish
Keep the surface of buttons, such as those in an elevator, free of bacteria and germs. These covers have a silver ion finish that stops bacteria, mold, mildew, fungi, and other microbes from growing for up to six months. They eliminate the need to clean elevator buttons between uses. Stick them to buttons using their adhesive back; there’s no need for special tools. All are clear, so you can still see what’s written on the buttons.