A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.

A molded cushion reduces vibration and wear from clamp edges, plus it provides a tighter fit around material than standard vibration-damping loop clamps.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.

Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Route pipe, tubing, and conduit across strut channel.

A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.

Clip these hangers onto the side of threaded rod. Unlike other threaded-rod-mount hangers, you can use more than one hanger on the same rod to organize multiple lines of pipe, tubing, and conduit.

A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.

Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.

Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.

Cut as much strap as you need to hang duct, pipe, and other materials.

For a strong, secure connection, mount these hangers by welding them to a rod.

Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.

A mounting plate provides a more secure hold at the mounting surface.

Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

Route bundles of wire and cable through a single hook. A wide opening allows access for installation, adjustment, and removal.

Also known as bridle rings, routing rings have an open-eye design that allows you to quickly install wire and cable.

Anchor these ringbolts where you need them, then remove the ring when not in use. Once installed, the mounting bolt stays in place. Insert the ring by threading into the mounting bolt; remove by unthreading it.

Temporarily mount routing rings and other threaded components to steel and iron surfaces.

Mount to a surface to secure and route cable.

Grip delicate cables with these holders.

Attach with a screw or other fastener.

Route and organize wire, cable, and hose along your DIN rail. Unlike zip ties, these cable ties can be temporarily undone to add or remove material.

Quickly attach and detach a bundle.

Use in noncritical applications, such as fencing, where the strength of a forged clamp is not required. Install clamps so the saddle is on the long (live) end and the U-bolt is on the short (dead) end. They’re also known as wire rope clips.

These clamps have a forged fabrication and are reliable in critical applications. They are not for making slings. These must be oriented with the saddle on the long (live) end and U-bolt on the short (dead) end. They’re also known as wire rope clips.

Constructed with a saddle for both the long (live) end and the short (dead) end, these clamps apply equal pressure without crimping or crushing the wire rope, so orientation doesn't matter. Also known as fist grip wire rope clips.

Make a removable loop without specialty tools for use in noncritical applications, such as fencing. Also known as tiller clamps.

A clamp and thimble in one convenient fitting simplifies installation while providing support and fray protection to the wire rope loop. Use a torque wrench to tighten the clamp.

Use these sleeves for non-lifting applications such as tethering, securing, and suspending.

Install these stud-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Install these eye-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Add a clevis end to wire rope without having to fray the rope or use a compression tool.

Compress sleeves with more force than hydraulic hand tools.