Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

Flexible grooves inside these polypropylene clamps allow material to expand and contract. Clamps are moisture and chemical resistant.

For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

Avoid the hassle of welding with these adhesive-mount clamps—they use a high-strength adhesive to form a permanent bond with the mounting surface—no additional tools required. Once assembled, the clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Mount to a surface and add a cable tie to secure a bundle.

Reduce gaps between the cable tie and bundle—these ties have a smooth body that allows them to adjust to the exact size of the material.

These ties are less likely to crack and break from dryness than regular cable ties.

Use these plastic cable ties when detection and retrieval are essential, such as in food processing applications. Ties are brightly colored for visibility and contain a special compound that can be picked up by X-ray equipment and metal detectors.

Pull the tab to tear off these cable ties.

These cable ties have a finely ribbed body and a metal-toothed head that allows them to adjust to the exact size of the material without slipping.

These ties meet UL flammability requirements.

Protect sensitive electronic equipment from static buildup.

These strong, wide ties are often used as an alternative to metal strapping.

With a thin, flexible body, these cable ties fit tightly around irregularly shaped bundles.

Create custom-length cable ties for large bundles and heavy materials.

Quickly attach and detach a bundle.

Stick these ties to any smooth, clean surface.

Create custom-length ties from a roll with hook on one side and loop on the other.

The buckle allows you to cinch these ties tight.

These ties meet UL flammability requirements.

Bundle cables outdoors with these ties that withstand exposure to UV rays and water.

The hook and loop on these ties holds more tightly than other hook and loop.

Use these mounts with stainless steel cable ties when working in corrosive environments.

The plastic coating on these ties adds an additional level of corrosion and abrasion resistance over other stainless steel cable ties.

Create custom-length ties for bundling delicate materials.

Formed to the shape of a round bundle, these ties close with a single twist of the top.

The softest of our twist ties, they have a cushioned outer layer for bundling delicate materials.

Secure large bundles such as lumber, cardboard, and wire coils.

These ties are wide and flat for a no-slip grip.

These clamps have a forged fabrication and are reliable in critical applications. They are not for making slings. These must be oriented with the saddle on the long (live) end and U-bolt on the short (dead) end. They’re also known as wire rope clips.

Install these clamps without any specific orientation, slide the nut over the rope and tighten it onto the threaded halves with a torque wrench.

Create a loop by feeding the wire rope through the clamp and tighten the set screw to secure it in place. Loosen the set screw to quickly adjust the loop. Also known as Gripple rope clamps. They are for use in noncritical applications, such as fencing.

Use in noncritical applications, such as fencing, where the strength of a forged clamp is not required. Install clamps so the saddle is on the long (live) end and the U-bolt is on the short (dead) end. They’re also known as wire rope clips.

Use these sleeves for non-lifting applications such as tethering, securing, and suspending.

Keep multiple sleeves on hand in a variety of sizes.

Also known as standard-pattern thimbles, these provide better protection against fraying than light duty thimbles.

These thimbles are also known as thin pattern thimbles.

Install these stud-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Install these swivel-hook-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Install these eye-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Add a mounting-plate to wire rope without having to fray the rope or use a compression tool.

Add an eye-end to wire rope without having to fray the rope or use a compression tool.

Also known as socket-end swage fittings, install these stud-end fittings with a roller swage press for a strong, permanent hold.

Also known as socket-end swage fittings, install these eye-end fittings with a roller swage press for a strong, permanent hold.

Feed the wire rope into the opening at the bottom of these hook-end fittings and through the body for a quick and simple installation.

Compress the thin shank wall with a hand tool to attach these light duty eye-end fittings. They are also known as hand swage fittings.

Compress the thin shank wall with a hand tool to attach these light duty clevis-end fittings. They are also known as hand swage fittings.