These cord grips are lightweight yet durable.

Made of nylon, these grips resist chemicals.

These grips have an extension that provides extra support for moving cables and prevents kinking for longer cable life.

Made of nylon, these grips resist chemicals.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Tighten the screws to secure your cable.

An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.

Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.

Tighten the screw-down clamp for superior pull-out resistance.

These grips are made of nylon, which resists most chemicals. The nylon mesh extension provides a secure hold when the cable is pulled or in motion.

Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from continuous submersion.

A rubber bushing with an oval slot provides liquid-tight entry for building cable, which is also known as Romex type NM-B or type UF-B.

Also known as cable-entry seals, the cable-entry side has heat-shrinkable polyolefin with an adhesive lining.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These stainless steel grips offer the most protection from wet, corrosive environments of any of our metal liquid-tight cord grips. They are rated IP67 for protection from temporary water submersion.

These 90° elbows meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.

The face of these grips is flush with the cable-entry point for a seamless appearance.

FDA compliant for direct food contact, these cord grips have a multi-piece design to wrap around cables in sanitary environments without removing connectors or rewiring.

Attach conduit and armored cable to a knockout in an outlet box or enclosure.

The loops tighten by the weight of your cable or by manual adjustment. These grips are often wrapped around a beam or pipe.

Made of stainless steel, these grips have excellent corrosion resistance.

These are tin-plated bronze.

Also known as socket-end swage fittings, install these eye-end fittings with a roller swage press for a strong, permanent hold.

Also known as socket-end swage fittings, install these stud-end fittings with a roller swage press for a strong, permanent hold.

Install these stud-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Install these clevis-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Install these swivel-hook-end plug-lock fittingson the end of wire rope for a strong hold and finished appearance.

Compress the thin shank wall with a hand tool to attach these light duty mounting-plate-end fittings. They are also known as hand swage fittings.

Compress the thin shank wall with a hand tool to attach these light duty clevis-end fittings. They are also known as hand swage fittings.

Add a stud end to wire rope without having to fray the rope or use a compression tool.

Add a clevis end to wire rope without having to fray the rope or use a compression tool.

Feed the wire rope into the opening at the bottom of these eye-end fittings and through the body for a quick and simple installation.

These clamps have a forged fabrication and are reliable in critical applications. They are not for making slings. These must be oriented with the saddle on the long (live) end and U-bolt on the short (dead) end. They’re also known as wire rope clips.

These clamps must be oriented with the saddle on the long (live) end and the U-bolt on the short (dead) end. They’re also known as wire rope clips.

Make a removable loop without specialty tools for use in noncritical applications, such as fencing. Also known as tiller clamps.

Use in noncritical applications, such as fencing, where the strength of a forged clamp is not required. Install clamps so the saddle is on the long (live) end and the U-bolt is on the short (dead) end. They’re also known as wire rope clips.

These compression sleeves are designed to meet lifting specifications.

These kits include two compression sleeves paired with two thimbles. The thimbles support the wire rope loops and prevent it from fraying.

Also known as standard-pattern thimbles, these provide better protection against fraying than light duty thimbles.

Also known as heavy-pattern thimbles, these can be used to reinforce the loop of a sling in accordance with ASME B30.9.

Screw the pin into position by hand for quick installation and removal. They're for use in low-vibration applications where the shackle remains stationary.

A bolt fastened with a nut and cotter pin makes these shackles more secure than screw-pin shackles.

A bolt fastened with a nut and cotter pin makes these shackles more secure than screw-pin shackles.

One end has a bolt fastened with a nut and cotter pin for a more secure connection than flush-pin connectors.

Attach a rope to the ring on the pin for remote release where access in limited. These shackles have an eye end for connecting to a hook.

Pull the collar to release the shackle from its locked position.

For use in low-vibration applications where the shackle remains stationary.

Indentations in the shackle body hold the head of the pin in place once fastened.

Minimize twisting and knotting of rope and chain.

A lip on the shackle keeps the pin from falling out when loosened.

Lock by screwing the latch into the body.