Suspend large and bulky items, such as coils of rope and step ladders. Wrap the strap around an item and then hook the buckle onto the mounting plate for a secure hold.

Use screws to mount these hooks to the ceiling or under a surface, such as a bench top.

Adhesive strips hold tight yet remove cleanly without damaging the wall.

Keep multiple bundles of wire and cable on separate hooks. The hooks have wide openings to allow access for installation, adjustment, and removal.

These plastic rings won't conduct electricity. Also known as distribution rings, they have a large opening for routing multiple cables. A smooth surface prevents damage to wire and cable.

Mount these ringbolts into a threaded hole, or use the nut for through-hole mounting. The pivoting ring allows material to move freely.

Hang these S-hooks from fencing and railing to route large bundles of material, such as cable, hose, and wire through your facility or worksite to avoid tripping hazards.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

Flexible grooves inside these polypropylene clamps allow material to expand and contract. Clamps are moisture and chemical resistant.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.

Attach with a screw or other fastener.

Feed a bundle through the closed loop and wrap the ends around pipe or conduit for support.

These ties are flexible, reusable, and adjustable for delicate bundles or bundles that frequently change in size.

Ties are made from heat-resistant aramid fabric to withstand temperatures up to 350° F.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

Bundle cables outdoors with these ties that withstand exposure to UV rays and water.

These ties stretch to hold material tightly without slipping.

Create a cable tie with a buckle—no sewing required.

Create custom-length ties from a roll with hook on one side and loop on the other.

The buckle allows you to cinch these ties tight.

Add push-in cable holder to this adapter to mount cable to DIN rail.

Keep individual wires separate by laying them between the coils on these holders.

Reduce gaps between the cable tie and bundle—these ties have a smooth body that allows them to adjust to the exact size of the material.

Rotating for easy positioning before a load is applied, these have a latch to ensure that rope, chain, and fittings won't separate from the hook when the load slackens.

These rotate for easy positioning before a load is applied. They have a latch to ensure rope, chain, and fittings won't separate from the hook when the load slackens.

These have a removable half-link to attach large rings, links, and other closed fittings.

A ball-bearing swivel allows these to rotate under load. Attach to chain by inserting the included pin through a link.

Screw these hooks into place and secure with the included nut.

For a more secure connection than standard hooks, the latch locks closed when a load is applied.

These have a latch that locks closed when a load is applied for a more secure connection than standard hooks. They rotate for easy positioning before a load is applied.

Slide the clevis pin into these hooks to attach chain, no extra fittings needed.

A spring-loaded pin ensures chain won't separate from the hook when the load slackens. Connect your chain to the clevis end.

Also known as foundry hooks, use these on thick molds, castings, and objects that don't have attachment points.

Easily slip chain, rope, and fittings on and off these open-mouth hooks. Attach your chain to the clevis end.

The latch ensures rope, chain, and fittings won't separate from the hook when the load slackens.

Weld these hooks into place.

Often used in binding and tie-down applications, these hooks have a narrow opening to securely hold a single link of chain.

These snaps have an eye that rotates for easy positioning.

Squeeze the trigger to quickly release the latch.

A wide opening accepts large diameters of rope and pipe. Squeeze the trigger to release.

The force of the load helps keep the arms closed. Press the trigger for quick connection and disconnection.

The narrow end restricts the movement of rope and chain, and the wide end allows room to attach multiple connectors.