These cable ramps handle heavy pedestrian and equipment traffic.

Curve these ramps to route cable around bends and corners in indoor areas with heavy pedestrian and equipment traffic.

Multiple channels let you separate different types of cable and cords.

These cable ramps are strong enough to withstand equipment traffic.

This wire duct completely encloses wire and cable.

Often used as an alternative to cable ties, wire duct guides and organizes short runs of electrical wiring in enclosures, control panels, and machines.

A slit along the length makes this sleeving easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

Rated UL 94 V-2, this sleeving resists combustion and minimizes the spread of flames. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. It has impact and abrasion resistance similar to conduit, with more flexibility.

The corrugated construction gives this sleeving impact and abrasion resistance similar to conduit, but with more flexibility.

The two halves of this sleeving nest into each other, fully enclosing contents. It has interlocking ridges that overlap to keep out dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

A strip of hook-and-loop creates a strong seal along the entire length of this sleeving, yet it can be opened at any point to access contents. Use it to wrap around wire, cable, or hose without disconnecting them.

Snaps keep this sleeving securely closed, yet permit quick access to contents and allow you to route wires in between the snaps. Use it to easily wrap around wire, cable, and hose without disconnecting them.

Organize and protect the cables on your Universal Robots arm without hindering its movement.

Silicone rubber coats this fiberglass sleeving to shed sparks and molten metal splash. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Coated with PVC, this polyester sleeving resists chemicals and solvents. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Often used to protect wire, cable, and hose in robotics and other automated applications, this highly flexible sleeving withstands continuous motion without tearing or fraying.

Wrap this sleeving around cable, cords and wires to protect them and to form bundles.

Made of PTFE, this sleeving has excellent resistance to chemicals and acids. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Braided from thick plastic strands, this sleeving has excellent abrasion resistance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

This sleeving stretches to fit over items for easy installation, and then tightens around its contents for a secure fit. Choose from multiple colors to organize wire and cable.

Tight braiding makes this sleeving resistant to fraying when cut with scissors. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.

A blend of Aramid and fiberglass gives this sleeving excellent abrasion resistance. It can withstand temperatures up to 650° F

This sleeving withstands temperatures over 1000°F, such as in refineries.

Tightly braided nylon fibers give this sleeving excellent abrasion resistance. As it wears, the fibers frizz and make the outer wall thicker for improved protection.

Add a layer of insulation to prevent electricity and heat from dissipating from wire and cable.

A specially formulated silicone rubber coating allows this sleeving to stretch over items during installation; it then tightens around its contents for a secure fit.

Made from thicker and denser fiberglass than standard spark-resistant sleeving, this sleeving is more abrasion resistant and provides better insulation. The silicone rubber coating protects against sparks and molten metal splash.

A mica and silicone rubber blend allows this sleeving to withstand temperatures up to 2100° F. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

Extend your cord’s life while stopping it from coming loose in places that are sanitized with water or steam as hot as 300° F, such as food plants and clean rooms.

Push to install these cord grips in wet environments and high-movement applications such as robotics and handheld equipment.

Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.

Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting.

Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.

Made of PBT, these grips resist soaking up water in washdown and other wet environments while securing cords with an extra-strong hold.

Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.

These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.

Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.

With an oval bushing hole, these lightweight grips secure flat building cable, such as Romex and Festoon cable, in wet areas. All offer strain relief to extend cable life.

Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.

Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.

Made of nylon, these grips resist chemicals.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Secure and seal electrical cords entering knockouts at a 45° angle.

Able to stand up to rust better than steel grips, these 300 series stainless steel grips secure electrical cables in corrosive environments.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These stainless steel grips offer the most protection from wet, corrosive environments of any of our metal wet-location cord grips. They are rated IP67 for protection from temporary water submersion.

The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

Stainless steel construction offers the most corrosion-resistance of any of our multi-diameter wet-location cord grips.

These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.

Attach a cord grip to cable without removing connectors and rewiring. These cord grips have a two-piece design to fit around cables with connectors.

These grips have a thin, flexible seal that covers the holes until you push cords through.

Thread cable and hose through the entire length.

Designed for smooth, quiet travel, these carriers minimize clicking and jumping in vibration-sensitive applications such as printing and scanning.

By completely surrounding the cable and hose, these carriers protect them from dirt, chips, and debris.

Use these accessories to mount carriers to your machinery without creating an obstruction.

Use this general purpose tubing to insulate and protect wire and cable.

Extra-thick walls provide more protection against abrasion and tears than standard high-shrink-ratio tubing. This tubing shrinks down to 1/6th of its original ID, so it creates a tight seal over irregularly shaped objects.

The smallest heat-shrink tubing we offer, this tubing protects wire with a 0.017" and smaller diameter.

Extra-thick walls provide better protection against abrasion and tears than standard moisture-seal tubing, as well as creating a water-resistant seal.

This PTFE tubing withstands temperatures up to 450° F and has an inner lining that creates a water-resistant seal when heated.