Pull one or more cables through conduit.

Pull wire and cable while maintaining tension until the line can be permanently anchored. Use these clamps with stranded bare steel wire and cable.

Flexible enough for pulling wire through multiple bends, this round, stainless steel tape is stiff enough to push through tough runs without backing up.

Safer to use around energized equipment than other types of fish tape, this fiberglass tape is also round, making it more flexible than flat and oval tape to pull wire through multiple bends.

The single loop can handle up to six 10-ga. bare wires at once.

As you pull with both hands, a latch grabs onto fish tape or pulling rope. Unlike pliers, this puller will not kink or slip off the fish tape.

With a handle and mounting hook for portability, these winches can move from job to job.

Remove the handle to wind these winches with a power drill.

One-piece gears provide more durability than the riveted gears of other hand winches. These winches move loads more gradually than standard hand winches. They take longer to wind but require less effort.

Tackle frequent lifting jobs with these rugged winches—their one-piece machined gears stand up to daily use.

These winches are stainless steel for corrosion resistance. Their one-piece machined gears stand up to daily use.

Tackle frequent lifting jobs with these rugged winches—their one-piece machined gears stand up to daily use.

An automatic brake holds the load, even when power is lost.

Because these winches run on compressed air, they give you longer operating times than electric winches.

These versatile pullers give you the capacity of a winch, and have a thick, rugged frame for long life. The wire rope on the pullers is stronger than rope and webbing but not as bulky as chain.

These versatile pullers are made of aluminum with stainless steel rope for corrosive environments. They give you the capacity of a winch in a portable tool. Wire rope is stronger than rope and webbing but not as bulky as chain.

Made of beryllium copper that is FM approved, these picks satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Position circuit board components without solder sticking to these picks.

The handle has a magnet at the end to pick up small steel objects. Use these picks to hold and position wire, springs, and other small parts.

These assorted picks have insulated handles that protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

A different tip at each end allows you to install, extract, and position parts with one tool.

Sets include a handle and an assortment of tips for holding and positioning wire, springs, and other small parts.

Change tips to use a different size or style pick for holding and positioning wire, springs, and other small parts.

Reach around obstructions and into tight spaces with picks that have long, angled tips. Use these tools to hold, separate, and position wire, springs, and other small parts.

A different tip at each end installs and positions tiny springs and wires. Unlike conventional picks that have pointed tips, these are rounded to prevent damage to sensitive components.

Similar to dental instruments, these needle-sharp picks are suitable for work around delicate circuits and components.

Avoid the potential for an arc flash or short circuit that can occur when using conventional insulated tools with metal components. Completely metal-free, these pliers are plastic with ceramic cutting blades. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Use to pull, bend, and cut wire.

When there isn't clearance to use standard-grip pliers, the angled head on these tools gives you access. Also known as lineman’s and combination pliers, use them to pull, bend, and cut wire.

Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.

Additional features, such as wire terminal crimpers, enable you to perform a variety of electrical wiring and installation work with a single tool. Also known as lineman’s pliers, use them to pull, bend, and cut wire.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. Use them to pull, bend, and cut wire.