These cord grips are lightweight yet durable.

The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

These grips install into enclosure holes quickly to stabilize and relieve strain on cords.

Made of nylon, these grips resist chemicals.

Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.

Tighten the screws to secure your cable.

An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.

These grips are sized to fit in tight areas.

Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.

These 90° elbows absorb less water and are less likely to crack or corrode than other types of plastics and metals.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.

Push to install these cord grips in wet environments and high-movement applications such as robotics and handheld equipment.

Keep moisture out of your enclosure while securing cords in wet environments. Made of polyamide, these grips are lightweight.

Tighten the screw-down clamp for superior pull-out resistance.

Secure cords in washdown areas where there’s minimal space—these cord grips curve 90° to relieve stress from bending.

These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.

Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.

Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.

Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.

With an oval bushing hole, these lightweight grips secure flat building cable, such as Romex and Festoon cable, in wet areas. All offer strain relief to extend cable life.

Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.

The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.

These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.

Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.

Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.

These grips are nickel-plated brass for good corrosion resistance.

These 90° elbows meet Class III, Divisions 1 and 2 standards for use in hazardous locations.

The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.

Peel away layers of rubber inserts to fit around cord grips, even when you don't know the exact diameter.

Attach a cord grip to cable without removing connectors and rewiring. These cord grips have a two-piece design to fit around cables with connectors.

These grips have a thin, flexible seal that covers the holes until you push cords through.

Install additional cables without swapping cord grips by pushing them through the thin, flexible seals on these grips, which have a sanitary design suitable for food-processing and pharmaceutical plants.

With a spring extension to prevent sharp bends, these bushings protects cords from wear and tear better than standard bushings.

Made of stainless steel, these grips have excellent corrosion resistance.

Made of stainless steel, these grips have excellent corrosion resistance.

Made of stainless steel, these grips have excellent corrosion resistance.

Protect RJ45 connectors on Ethernet cables from strain when cables are pulled and bumped.