This sleeving absorbs UV light, so it can be used in direct sunlight without getting damaged. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Made with a self-extinguishing additive, this sleeving will not produce fumes when exposed to open flame or high temperatures. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

A strip of hook-and-loop creates a strong seal along the entire length of this sleeving, yet it can be opened at any point to access contents. Use it to wrap around wire, cable, or hose without disconnecting them.

Zip this sleeving around wire, cable, or hose that are connected at both ends to quickly bundle them.

The tightly braided construction makes this polyester sleeving abrasion resistant. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Often used to protect wire, cable, and hose in robotics and other automated applications, this highly flexible sleeving withstands continuous motion without tearing or fraying.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

Unlike traditional sleeving that bunches wire and cable into a circle, this sleeving holds them flat, so it’s good for tight spaces such as vehicle interiors. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

This sleeving stretches to fit over items for easy installation, and then tightens around its contents for a secure fit. Choose from multiple colors to organize wire and cable.

Rated UL 2024 and NFPA 262, this sleeving is approved for use in plenum spaces such as duct work and above a drop ceiling. It self-extinguishes and emits minimal amounts of smoke and gas during combustion. Stretch to fit over items for easy installation; it tightens around its contents for a secure fit.

Braided from thick plastic strands, this sleeving has excellent abrasion resistance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Use this braided copper sleeving to protect wire and cable from signal distortion caused by nearby equipment and devices. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

A specially formulated silicone rubber coating allows this sleeving to stretch to twice its relaxed ID to fit over items during installation; it then tightens around its contents for a secure fit.

Add a layer of insulation to prevent electricity and heat from dissipating from wire and cable.

Made from thicker and denser fiberglass than standard spark-resistant sleeving, this sleeving is more abrasion resistant and provides better insulation. The silicone rubber coating protects against sparks and molten metal splash.

With a temperature rating of 1800°F or higher, this sleeving can withstand hotter temperatures than fiberglass and most ceramic.

A blend of Aramid and fiberglass gives this sleeving excellent abrasion resistance. It can withstand temperatures up to 650° F

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

Made of nylon, this sleeving is the most impact- and abrasion-resistant slit corrugated sleeving we offer. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them.

This sleeving reflects heat away from contents and withstands temperatures up to 300°F. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

A hinge along the entire length makes this one-piece sleeving easy to open for installation. Interlocking ridges overlap along the opening to protect contents from dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

This sleeving reflects heat away from contents and withstands temperatures up to 900°F. The corrugated construction gives it impact and abrasion resistance similar to conduit, but with more flexibility.

Made of neoprene rubber, this sleeving has excellent abrasion resistance. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

Often used in automated applications such as robotics, this highly flexible silicone rubber tubing withstands continuous motion without cracking and tearing. It resists abrasion and can be dragged over rough surfaces without damage.

This tubing creates a tight seal over irregularly shaped objects.

The smallest heat-shrink tubing we offer, this tubing protects wire with a 0.017" and smaller diameter.

Access connections more easily than with standard heat-shrink tubing. Make a small slit in this tubing to peel it away.

Extra-thick walls provide better protection against abrasion and tears than standard moisture-seal tubing, as well as creating a water-resistant seal.

Made of PVC, this tubing resists chemicals, oil, and solvents. The adhesive lining creates a water-resistant seal when heated.

Use this tubing where wire and cable may be exposed to chemicals, oil, and acids.

Often used to bundle batteries, capacitors, and other electronics, this tubing tightly conforms to objects, similar to shrink wrap. It has excellent resistance to chemicals, oil, and acids.

Use this tubing in applications where temperatures reach up to 500° F. It's often used to insulate electronic components.

Protect bus bars and other high-voltage devices—this tubing withstands voltages up to 15,000 volts.

Also known as halogen-free tubing, this tubing produces minimal amounts of smoke and gas if exposed to an open flame, so it can be used in enclosed areas such as ships and tunnels.

Made of PVDF, this tubing has excellent cut and abrasion resistance. It has a flame-retardant additive that resists combustion and minimizes the spread of flames.

After being cleaned with alcohol, this tubing is bagged and sealed in a clean room. It's certified for material quality and purity.

Organize and route wire and cable in an enclosure—this tubing bundles wires together while allowing them to reach different connection points.

Create a permanent seal without applying heat. This tubing is also known as cold-shrink tubing.

Seal the end of crimped connections, such as motor coils, to protect them from moisture.

Maintain a supply of tubing in a variety of sizes that withstand abrasion, moisture, and chemicals.

Flexible enough for small bundles, these ties are often used for electronics.

These ties meet UL flammability requirements.

Create custom-length ties from a roll with hook on one side and loop on the other.

The buckle allows you to cinch these ties tight.

Ties are made from heat-resistant aramid fabric to withstand temperatures up to 350° F.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

Create a cable tie with a buckle—no sewing required.

Quickly attach and detach a bundle.

Route and organize wire, cable, and hose along your DIN rail. Unlike zip ties, these cable ties can be temporarily undone to add or remove material.

Easily transport or hang cords, rope, and hose—these hook and loop cable ties include a handle.

The buckle allows you to cinch these ties tight.

These cable ties come with a material certificate with traceable lot number and product shelf life.

These ties meet UL flammability requirements.

The head of these cable ties is contoured to fit against pipe, tubing, and other round material for a tight fit.

Use the built-in blade to remove excess length once these ties are secure.

These ties are less likely to crack and break from dryness than regular cable ties.

With a thin, flexible body, these cable ties fit tightly around irregularly shaped bundles.

Create custom-length cable ties for large bundles and heavy materials.

Whether you plan to change the bundle size or need a temporary hold, these ties have a release tab for removal and reuse.

For use in environments subjected to chemicals, these ties withstand the most corrosive conditions.

A foam padded back combined with an extra-wide body protects sensitive bundles, such as fiber optic cable.

Pull the tab to tear off these cable ties.

Attach these cable ties directly to a surface—no separate mount needed.

Keep an assortment of cable ties on hand.

Formed to the shape of a round bundle, these ties close with a single twist of the top.

Ties come on a spool for use in a twist tie machine.

Create strong and durable custom-length ties with a hard rubber coating and wire core.

The evenly spaced ball-shaped beads allow you to adapt to changes in bundle size.

The ripple in the body prevents over tightening and allows for expansion to protect material that frequently changes size, such as heat cable.

The plastic coating on these ties adds an additional level of corrosion and abrasion resistance over other stainless steel cable ties.

Stamp or emboss these ties to identify material.

Use in light duty applications such as tagging and attaching documentation to equipment.

Also known as mastic tape, this tape is thicker than other electrical tape to cushion, insulate, and seal out moisture and environmental contaminants in electrical connections.

At only 0.0025" thick, this tape combines conformability with durability and abrasion resistance.

In the event of a fire, this rubber tape expands to protect cables from flames and heat.

No need for adhesive—this tape fuses to itself for a permanent seal and stretches to fit virtually any form. Also known as cold shrink tape.

This polyester tape has a woven mesh edge that conducts electricity. Use it to shield cables and electronic components from EMI (electromagnetic interference).

Use this tape to modify printed circuit boards, shield components, and prototype wiring-board layout and design.

Backed with 3M VHB 4941 foam adhesive for strength, padding, and vibration resistance.

A strong, thick layer of Teflon® PTFE makes this tape tougher than standard Low-Friction Tape Made with Teflon® PTFE.

Highly resistant to impact, tearing, and corrosive chemicals, use FEP tape to line chutes and hoppers and to cover shelves in laboratories.

Providing all-weather corrosion protection, this vinyl tape resists salt water, UV light, acids, and alkalies. Use it to wrap pipes and electrical conduit both above and below ground.