Size Size |
|---|
|
|
|
Decimal Size Equivalent Decimal Size Equivalent |
|---|
|
|
|
For Drilling Type For Drilling Type |
|---|
|
Finish Finish |
|---|
|
Component Component |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
About Masonry Drill Bits
More
Drill Bit Decimal Size Equivalents
More
About Drill Bits
More
Changeable-Size SDS-Max-Shank Masonry Core Drill Bits for Rotary Hammers
These bits allow you to switch to another size by changing only the bit body. They are hollow and cut with their outside edge for drilling large holes. The SDS-Max shank has three deep slots and two shallow slots for use with SDS-Max-drive rotary hammers. They cannot be used with SDS-Plus-drive rotary hammers.
Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. This type of bit drills faster and penetrates material with less pressure than rotary-only bits. Also known as percussion or impact bits. To achieve maximum drilling depth, break up and remove the core every 4” before drilling deeper.
For technical drawings and 3-D models, click on a part number.
| Size | Decimal Size Equivalent | Overall Lg. | Material | Specifications Met | Each | |
| 1 1/2" | 1.5" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 0000000 |
| 1 3/4" | 1.75" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 2" | 2" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 2 1/2" | 2.5" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 3" | 3" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 3 1/2" | 3.5" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 4" | 4" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 4 1/2" | 4.5" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| 5" | 5" | 5" | Uncoated Carbide-Tipped Steel | ANSI B212.15 | 0000000 | 000000 |
| Material | Each | |
| Steel | 00000000 | 000000 |
| For Drill Bit Size | Material | Each | |
| 1 1/2", 1 3/4", 2 1/2", 2", 3 1/2", 3", 4 1/2", 4", 5" | Carbide-Tipped Steel | 0000000 | 000000 |
SDS-Max-Shank Masonry Core Drill Bits for Rotary Hammers
These hollow bits cut with their outside edge for drilling large holes. The SDS-Max shank has three deep slots and two shallow slots for use with SDS-Max-drive rotary hammers. They cannot be used with SDS-Plus-drive rotary hammers. Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. This type of bit drills faster and penetrates material with less pressure than rotary-only bits. Also known as percussion or impact bits. The included pilot drill makes starting holes easier.
| Size | Decimal Size Equivalent | Shank Type | Point Style | Specifications Met | For Use On | Includes | Max. Drilling Dp. | Each | |
12" Overall Lg. | |||||||||
|---|---|---|---|---|---|---|---|---|---|
Inch | |||||||||
Uncoated Carbide-Tipped Steel | |||||||||
| 1 3/4" | 1.75" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill, Core Ejector Key | 7" | 00000000 | 0000000 |
| 2" | 2" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill, Core Ejector Key | 7" | 00000000 | 000000 |
| 2 5/8" | 2.625" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill, Core Ejector Key | 7" | 00000000 | 000000 |
| 3 1/4" | 3.25" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill, Core Ejector Key | 7" | 00000000 | 000000 |
| 3 9/16" | 3.5625" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill, Core Ejector Key | 7" | 00000000 | 000000 |
22" Overall Lg. | |||||||||
Inch | |||||||||
Uncoated Carbide-Tipped Steel | |||||||||
| 1 3/4" | 1.75" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill, Core Ejector Key | 17" | 00000000 | 000000 |
| 2" | 2" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill, Core Ejector Key | 17" | 00000000 | 000000 |
| 2 5/8" | 2.625" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill, Core Ejector Key | 17" | 00000000 | 000000 |
| 3 1/4" | 3.25" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill, Core Ejector Key | 17" | 00000000 | 000000 |
| 4" | 4" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill, Core Ejector Key | 17" | 00000000 | 000000 |
| 5" | 5" | SDS Max | Standard | ANSI B212.15 | Masonry, Concrete | Pilot Drill, Core Ejector Key | 17" | 00000000 | 000000 |
| Replacement Pilot Drill with Core Ejector Key | 00000000 | Each | 000000 |
Changeable-Size Spline-Shank Masonry Core Drill Bits for Rotary Hammers
These bits allow you to switch to another size by changing only the bit body. They are hollow and cut with their outside edge for drilling large holes. The shank has 12 splines for use with a spline-drive rotary hammer. Drill holes using simultaneous rotary and hammering action to break masonry material into tiny granules. This type of bit drills faster and penetrates material with less pressure than rotary-only bits. Also called percussion or impact bits.
For technical drawings and 3-D models, click on a part number.
| Material | Each | |
| Steel | 00000000 | 000000 |
Hex-Shank Masonry Core Drill Bits for Rotary-Only Drilling
These hollow bits cut with their outside edge for drilling large holes. Instead of using a hammering action to break up masonry material, these bits drill with rotary action only, requiring more pressure to grind up material. Use with handheld power drills, drill presses, and in hammer drills set to rotary-only mode. Do not use in hammering applications. To achieve maximum drilling depth, break up and remove the core every 4” before drilling deeper.
Pilot drills (sold separately) make starting holes easier.
For technical drawings and 3-D models, click on a part number.
Drill Bits | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Shank | Length Extensions | Pilot Drills | |||||||||||||
| Size | Decimal Size Equivalent | Overall Lg. | Max. Drilling Dp. | Type | Size | Specifications Met | For Use On | Each | Shank Size | Overall Lg. | Each | Each | |||
Inch | |||||||||||||||
Uncoated Carbide-Tipped Steel | |||||||||||||||
| 1" | 1" | 9" | 7" | Hex | 1/2" | ANSI B212.15 | Masonry, Concrete | 0000000 | 0000000 | 1/2" | 18" | 0000000 | 000000 | 000000 | 00 |
| 1" | 1" | 12" | 10" | Hex | 1/2" | ANSI B212.15 | Masonry, Concrete | 0000000 | 000000 | 1/2" | 18" | 0000000 | 00000 | 000000 | 00 |
| 1 1/4" | 1.25" | 12" | 10" | Hex | 1/2" | ANSI B212.15 | Masonry, Concrete | 0000000 | 000000 | 1/2" | 18" | 0000000 | 00000 | 000000 | 00 |
| 1 1/2" | 1.5" | 12" | 10" | Hex | 1/2" | ANSI B212.15 | Masonry, Concrete | 0000000 | 000000 | 1/2" | 18" | 0000000 | 00000 | 000000 | 00 |
| 1 3/4" | 1.75" | 12" | 10" | Hex | 1/2" | ANSI B212.15 | Masonry, Concrete | 0000000 | 000000 | 1/2" | 18" | 0000000 | 00000 | 0000000 | 000000 |
| 2" | 2" | 12" | 10" | Hex | 1/2" | ANSI B212.15 | Masonry, Concrete | 0000000 | 000000 | 1/2" | 18" | 0000000 | 00000 | 0000000 | 00000 |
| 2 1/2" | 2.5" | 12" | 10" | Hex | 1/2" | ANSI B212.15 | Masonry, Concrete | 0000000 | 000000 | 3/4" | 18" | 0000000 | 00000 | 0000000 | 00000 |
| 3" | 3" | 12" | 10" | Hex | 1/2" | ANSI B212.15 | Masonry, Concrete | 0000000 | 000000 | 3/4" | 18" | 0000000 | 00000 | 0000000 | 00000 |
SDS-Max-Shank Hollow Masonry Drill Bits for Dust Containment
When connected to a vacuum, these hollow bits can suck up concrete dust while drilling to help meet OSHA standards for silica dust exposure. They can also be used to clean out holes for installing adhesive anchors. The SDS-Max shank has three deep slots and two shallow slots for use with SDS-Max-drive rotary hammers. They cannot be used with SDS-Plus-drive rotary hammers.
| Size | Decimal Size Equivalent | Overall Lg. | Max. Drilling Dp. | Shank Type | Point Style | For Vacuum Hose ID | For Use On | Each | |
Inch | |||||||||
|---|---|---|---|---|---|---|---|---|---|
Titanium-Nitride (TiN) Coated Carbide-Tipped Steel | |||||||||
| 3/4" | 0.75" | 21" | 12 1/2" | SDS Max | Standard | 1 3/8" | Masonry, Concrete | 000000 | 0000000 |
| 13/16" | 0.8125" | 25" | 15" | SDS Max | Standard | 1 3/8" | Masonry, Concrete | 000000 | 000000 |
| 7/8" | 0.875" | 25" | 15" | SDS Max | Standard | 1 3/8" | Masonry, Concrete | 000000 | 000000 |
| 1" | 1" | 27" | 17 1/2" | SDS Max | Standard | 1 3/8" | Masonry, Concrete | 000000 | 000000 |
| 1 1/8" | 1.125" | 29" | 20" | SDS Max | Standard | 1 3/8" | Masonry, Concrete | 000000 | 000000 |
| 1 3/8" | 1.375" | 35" | 25" | SDS Max | Standard | 1 3/8" | Masonry, Concrete | 000000 | 000000 |
SDS-Plus-Shank Hollow Masonry Drill Bits for Dust Containment
When connected to a vacuum, these hollow bits can suck up concrete dust while drilling to help meet OSHA standards for silica dust exposure. They can also be used to clean out holes for installing adhesive anchors. The SDS-Plus shank has two deep slots and two shallow slots for use with SDS-Plus-drive rotary hammers. They cannot be used with SDS-Max-drive rotary hammers.
| Size | Decimal Size Equivalent | Overall Lg. | Max. Drilling Dp. | Shank Type | Point Style | For Vacuum Hose ID | For Use On | Each | |
Inch | |||||||||
|---|---|---|---|---|---|---|---|---|---|
Titanium-Nitride (TiN) Coated Carbide-Tipped Steel | |||||||||
| 7/16" | 0.4375" | 13" | 7 1/2" | SDS Plus | Standard | 1 3/8" | Masonry, Concrete | 000000 | 000000 |
| 1/2" | 0.5" | 13" | 7 1/2" | SDS Plus | Standard | 1 3/8" | Masonry, Concrete | 000000 | 00000 |
| 9/16" | 0.5625" | 15" | 10" | SDS Plus | Standard | 1 3/8" | Masonry, Concrete | 000000 | 000000 |
| 5/8" | 0.625" | 15" | 10" | SDS Plus | Standard | 1 3/8" | Masonry, Concrete | 000000 | 000000 |
| 11/16" | 0.6875" | 18" | 12 1/2" | SDS Plus | Standard | 1 3/8" | Masonry, Concrete | 000000 | 000000 |
| 3/4" | 0.75" | 18" | 12 1/2" | SDS Plus | Standard | 1 3/8" | Masonry, Concrete | 000000 | 000000 |