With a thickness that's precision ground to a tight tolerance, these bars are sometimes called flat stock.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

Coated with an aluminum-silicon alloy, these sheets resist corrosion while withstanding long-term exposure to high temperatures. Use in drying ovens, furnaces, and smokestacks.

The galvannealed coating allows these steel sheets to be painted without prepping the surface. They're easier to weld and more scratch resistant than zinc-galvanized steel sheets. Use them for outdoor signs, cabinets, and doors.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

These rods are zinc galvanized for good corrosion resistance.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

These 90° angles are zinc galvanized for good corrosion resistance.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

This wire is zinc galvanized for good corrosion resistance.

Also known as mild steel, use these low-carbon steel balls in parts that don't require high strength.

Made of stiff low-carbon steel to deflect less under load, these H-bars are commonly used in machine bases, construction, platforms, and frames.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

Precision ground and held to a strict tightness tolerance, these rods are ready for turning in a lathe.

A lead-free alternative to 12L14, 1215 carbon steel contains the same amount of sulfur and phosphorus for excellent machinability. It is often used for shaft couplings, studs, and pins.

The lead additive acts as a lubricant, which allows 12L14 carbon steel to withstand very fast machining. It's used to fabricate a wide variety of machine parts.

The lead additive acts as a lubricant, which allows 12L14 carbon steel to withstand very fast machining. It's used to fabricate a wide variety of machine parts.

These rods are precision ground and held to a strict straightness tolerance, so they're all set for turning applications in your lathe.

1117 carbon steel responds to surface-hardening heat treatment better than other easy-to-machine carbon steels. Use it to fabricate shaft couplings, studs, pins, and universal joints.

Stronger than low-carbon steel with equally good machinability, 1045 carbon steel is widely used for bolts, studs, and shafts.

This UHSS (ultra high-strength steel) allows you to fabricate high-strength parts using thinner material than you could with other types of steel. It is formable, weldable, and more economical than alloy steel.

Keep shim stock in a variety of thicknesses on hand with these sets. Cut into custom shapes to fit your application.

Also known as machinery bushings, these shims have an oversized OD to create a larger bearing surface for reduced wear between moving parts.

Be prepared with ring shims in a variety of thicknesses. These shims fit around fasteners and shafts to precisely align, level, and adjust spacing.

Be prepared with shims in a variety of thicknesses. Also known as arbor spacers, these shims are notched to fit over keyed shafts.

Be prepared with shims in a variety of thicknesses. These shims are shaped to fit over D-profile shafts. Use them to precisely align, level, and adjust spacing.

Send us a drawing, and we'll cut your custom shim.

Use a single shim on feet or positioning arms that are secured with multiple fasteners. The slots let you insert, remove, and adjust the shims without disassembling your machinery. Also known as finger shims.

Use round shims to precisely align, level, and adjust spacing on shafts and machinery.

Eight times straighter than standard rotary shafts, these tight-tolerance shafts minimize vibrations and reduce wear to bearings and other components. They also have diameter tolerances that are twice as tight as standard rotary shafts.

These shafts have keyways only on the ends, leaving a plain shaft in the center. Use the keyways with machine keys to transmit torque to gears, sprockets, and other keyed components. Use the middle of the shaft with bearings and other round-bore components.

Mount the flange to a machine or wall to support idler sprockets and pulleys in tensioning applications. They include washers and a nut to position your component and hold it in place.

Clip retaining rings into the grooves to separate and position gears, sprockets, and bearings.

Connect these internally threaded shafts directly to threaded components, or use a fastener to secure. They have a flat surface area that allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.

Connect these internally threaded shafts directly to threaded components, or use a fastener to secure.

A shoulder near the end of the shaft provides a stop for gears, sprockets, and bearings.

With 2" of each end softened, it's easier to machine a custom end for mounting. The rest of the shaft is case-hardened, which increases hardness and wear resistance on the surface of the shaft while allowing the center to remain soft for absorbing stresses caused by shifting loads.

Keep a material certificate on hand for compliance and quality assurance needs. Certificates include a traceable lot number and material test report. These hollow shafts reduce system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Clip retaining rings into the grooves to separate and position collars, supports, and housings.

A shoulder near the end of the shaft allows for easy positioning of housings, shaft supports, and collars.

Replace worn shafts in two-piece support-rail shaft systems, or mate with a support rail to create your own. The tapped mounting holes match those on our Support Rails.