Fit these through existing holes and mark the center of the hole in a second workpiece.

Also known as blind-hole spotters, these punches fit into closed-end holes and mark the center of a complementary hole.

Push down on the spring-loaded cone to center the punch in a variety of round and square hole sizes.

These sets come with three punches for use with a variety of hole sizes. Insert one into an existing hole and twist the handle to open the end of the punch. The point automatically centers once the punch has fit the hole size.

Also known as transfer screws, the punches in these sets can be used in any threaded hole to transfer the hole location. Use the handle to screw a punch into a hole.

The punches in these sets have a uniform shoulder height so you can quickly transfer multiple hole locations at once. Also known as transfer screws.

Find the center of square and round materials, such as structural framing and pipe, and determine setup angles on milling machines and grinders.

Also known as center punches, strike these with a hammer to mark hole centers in metal and other materials.

Strike these Starrett punches with a hammer to mark hole centers in metal and other materials. Also known as center punches.

Ground to a sharper tip than other center-marking punches, these tools make the precision marks required for the intersection of lines and other detailed tasks. They're also known as prick punches.

With an internal spring mechanism, these Starrett punches offer one-hand operation when marking hole centers.

Center your work by mounting these into your drill chuck or collet and lining up the pointer with the mark on the shaft.

These light duty centers are for intermittent use on manual lathes.

Also known as bull-nose centers, these have a wide head to hold pipe and large-diameter tubing.

Maintain consistent alignment in mating parts by installing a pin in one part and a liner in the other.

The shoulder provides a consistent height reference point and keeps the pin from being pressed through the fixture.

A slightly undersized shank makes these pins easy to install and replace. Also known as slip-fit and lock-screw locating pins, they are held in place by a separate lock screw.

The head on these pins slides side-to-side in one direction. Use one of these pins and one standard round-head pin to prevent jamming when loading and unloading workpieces with inconsistent hole spacing.

A good choice for automated clamping, these retractors use compressed air to extend and retract a locating pin, protecting the pin from damage in applications where fixtures move through a process, such as along a conveyor belt.

Precisely align drilled holes in two parts.

Hold tiny workpieces in these compact vises.

For big jobs, these vises have a wider jaw opening, deeper throat depth, and larger footprint than standard vises.

Designed for outdoor use, these vises have a finish that resists corrosion.

The head tilts and locks in place to hold work at an angle.

A bright yellow vise body stands out on the shop floor.

The movable jaw can be repositioned to extend the jaw opening. Pull out the entire sliding section and insert it on the opposite side of the vise.

These V-shaped liners hold large round material.

Fold the pliable tabs over the jaws to install.

Also known as woodworkers' vises, these mount to the underside of your workbench and sit flush with the surface.

Insert these one-piece grooved liners between vise jaws to hold small-diameter material vertically.

Clamp tubing into these holders to keep it steady while you cut, flare, or expand the end.

The jaws are rubber coated to prevent damage to pipe and other round workpieces.

Secure these heavy duty vises to the back of a truck to clamp at your job site.

Replace your try square, miter square, depth gauge, height gauge, center-point finder, and level. The blade on these squares meets Fed. Spec. GGG-R-791H, which establishes uniform standards for accuracy, graduations, and size.

Attach to High-Accuracy Combination Square Blades with the included lockbolts.

Use these squares in place of your try square, miter square, depth gauge, height gauge, center-point finder, and level.

Install these gauges onto the jaws of electronic, dial, and vernier calipers to measure the center-to-center distance between two holes.

Find the edge of a workpiece, align your setup, and inspect parts with one tool. Once installed in your milling machine spindle, these indicators can measure in three axes.

Find tube, pipe, fastener, wire, and drill bit sizes with one tool.

Line up holes by driving these pins through existing rivet, pin, and bolt holes in multiple pieces of metal. Alternatively known as lineup taper punches.

Turn the pin and the tapered shaft forces the two holes into alignment.

When one side wears out, use the other one.

These brass tools reduce marring on metal surfaces because they're softer than steel punches.

Contains pin-loosening, pin-removal, and center-marking punches as well as chisels.

Insert directly into power screwdrivers, impact drivers, and other tools that accept a 1/4" hex shank.

Keep padlocks, tags, and other lockout tools neatly stored and ready for use in these easy-to-spot stations.

Sets contain items for group electrical and valve lockouts and are furnished in a yellow plastic case that mounts to the wall to keep the items organized in a central location.

Carry these boxes from job to job and mount them near valves or electrical controls to save time when organizing group lockouts.

Give employees access to Safety Data Sheets (SDS) and training booklets according to OSHA's Hazard Communication Standards.