These surface fillers come in a pen for precision application. After applying, use the LED on the back of the pen to instantly cure. They can be used with most types of metal as well as ceramic, stone, and porcelain.

Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater. Use them to repair cracked, worn, and damaged surfaces. Size listed is the combined total of the two parts.

Paste fillers resist alkalies, solvents, gasoline, and oil.

Able to withstand temperatures up to 2300° F, these ceramic surface fillers are often used as thermal insulation on brick, mortar, burner blocks, furnace holders, and thermocouples.

Repair small leaks and cracks in coolant systems for commercial vehicles and industrial equipment. These surface fillers meet ASTM D3147 for their ability to stop leaks in engine cooling systems. Pour them into your coolant to fix both internal and external leaks. They contain ceramic microfibers and copper particles to create a permanent seal. They’re compatible with antifreeze and other coolant system additives.

Also known as sloshing compounds, these two-part epoxies bond to rough and rusty surfaces in fuel tanks to repair leaks and prevent further corrosion. They withstand permanent immersion in fuel, oil, and harsh solvents. Use them with metal, plastic, and fiberglass tanks. Mix the smaller can with the bigger one and pour into your fuel tank. Rotate the tank to coat the interior and dump out any excess. Allow to cure overnight. Size listed is the combined total of the two parts.

1.5-pint container can treat a 10-gallon fuel tank. 3-pint container can treat a 20-gallon fuel tank.

Stop slow-flowing and weeping leaks in concrete. These crack fillers begin to harden in three to five minutes to create a permanent fix that won't shrink.

Polyurethane fillers are thin to penetrate deep into cracks. When fully cured they create a seal that can withstand pressure of up to 2,000 psi. Apply with a standard caulk gun (sold separately). For especially large cracks, use a packer (sold separately) with a grease gun or a grout pump.

Stop active leaks of up to 50 gallons per minute in concrete, brick, and stone. These crack fillers begin to harden within seconds to create a permanent fix that won't shrink. When fully cured they create a seal that can withstand pressure of up to 2,000 psi. Apply with a dispensing gun (sold separately). The size listed is the combined total of the two parts. A mixer nozzle is included.

Fill in and shape horizontal, vertical, and overhead concrete surfaces, such as steps and columns.

Epoxy surface fillers are nonsagging. They resist oil, grease, water, alkalies, and chemicals. Application time, after mixing, is 1 hour. The size listed is the combined total of the two parts.

Mix this two-part epoxy—a resin-aggregate blend and a pigmented hardener—to create a grout that resists chemicals, such as acids, alkalies, salt water, and common solvents and cleaners. Its lightweight formula makes this grout easy to spread. Use in horizontal or vertical joints—grout won’t sag or shrink. Apply with a grout float. It can be cleaned up with water when wet; it doesn’t require a sealer once it cures. The size listed is the combined total of the two parts.

Used on ceramic, concrete, and stone floor and wall tiles, grout consists of fine sand, masonry cement, and coloring. Apply with a grout float.

Mix cement grout with water.

Acrylic grout does not require mixing. It resists shrinking, cracking, and staining.

Keep the surface of your porcelain fixtures looking like new.

Filler repairs large chips and cracks. Sand and finish with glaze.

Glaze touches up small chips and scratches.

Pull off a small piece of putty and stick lightweight objects to your surface. It removes without leaving stains or residue on most surfaces and is reusable.

This putty-like glue cures into a pliable rubber. Use it to repair seals and cracks, or mold it into hooks and bumpers.

Temporarily stabilize objects on flat surfaces with this clear adhesive gel. It removes cleanly from most surfaces with a twist, and it won't dry out so it can be used again.

These machinable epoxies are mixed with metal so they can be used to repair cracks and threaded holes. The strongest and most weather- and chemical-resistant structural adhesives, epoxies work especially well on metals. For putty adhesives, slice off the required amount, then knead it together to form a moldable adhesive.

8267 is reinforced with steel, but won't rust.

Epoxies are the strongest and most weather- and chemical-resistant structural adhesives. They work especially well on metals. For putty adhesives, slice off the required amount, then knead it together to form a moldable adhesive.

For quick repairs, these epoxies begin to harden in 6 minutes or less. Epoxies are the strongest and most weather- and chemical-resistant structural adhesives.

The size listed is the combined total of the two parts.

50132 works especially well on plastics and composites.

To allow time to adjust and position parts, these epoxies remain workable for at least 90 minutes. The strongest and most weather- and chemical-resistant structural adhesives, epoxies work especially well on metals.

The size listed is the combined total of the two parts.

Urethane adhesives are the most flexible, so they bond dissimilar materials and damp vibration.

The size listed is the combined total of the two parts.