Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

A blend of Aramid and fiberglass gives this sleeving excellent abrasion resistance. It can withstand temperatures up to 650° F

With a temperature rating of 1800°F or higher, this sleeving can withstand hotter temperatures than fiberglass and most ceramic.

Coated in acrylic, this sleeving holds up to rapid temperature changes, and it won’t break down from refrigerants, solvents, oil, or lubricants. Also known as hermetic sleeving, it’s designed to protect wires and hose inside air-tight motors, such as those used in air conditioners.

Tight braiding makes this sleeving resistant to fraying when cut with scissors. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Protect wire and cable from signal distortion caused by nearby equipment and devices. Expandable, this sleeving stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

With excellent torsional strength, this sleeving withstands the extreme twisting found in robotics. It has impact strength similar to steel yet is lighter than most other sleeving materials. Stretch it to fit over items for easy installation; it tightens around its contents for a secure fit.

Made of PPS plastic, this sleeving shields cable, hose, and pipe from oil, acids, and other chemicals. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Tested to meet MIL-STD-202, this sleeving meets performance standards for flame retardance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Use this PTFE sleeving in applications where temperatures reach up to 500° F.

A silicone rubber coating on this fiberglass sleeving protects against sparks and molten metal splash.

Add a layer of insulation to prevent electricity and heat from dissipating from wire and cable.

Organize and protect the cables on your Universal Robots arm without hindering its movement.

Wrap this sleeving around wire, cable, and hose without disconnecting them. It has a slit along the entire length and wraps over itself to stay closed without an adhesive strip or other closure.

Silicone rubber coats this fiberglass sleeving to shed sparks and molten metal splash. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

Unlike traditional sleeving that bunches wire and cable into a circle, this sleeving holds them flat, so it’s good for tight spaces such as vehicle interiors. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

Insulate your wire, cable, and hose in continuous temperatures up to 400° F and easily access them. This sleeving opens anywhere along its length with a hook-and-loop strip.

To stop rodents from chewing on this sleeving and damaging your wire, cable, or hose, it’s reinforced with glass fibers that irritate rodents’ gums. Wrap it around components without having to disconnect them.

Often used in robotics and other automated applications, this sleeving adds an extra layer of protection and insulation to cable and hose carriers.

This sleeving absorbs UV light, so it can be used in direct sunlight without getting damaged. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

With a unique overlapping link structure, you can open and close this sleeving like a zipper using the included tool. The tool’s open design and the slots in the sleeving make it easy to branch off wires from your bundle as you’re zipping it shut.

Made with a self-extinguishing additive, this sleeving will not produce fumes when exposed to open flame or high temperatures. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Made of PTFE, this sleeving has excellent resistance to chemicals and acids. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Made for bundling wire, cable, and hose in high-traffice areas—this sleeving is HDPE plastic, so it stands up to wear and crushing forces better than standard spiral sleeving.

With a copper and nickel exterior and conductive lining, this sleeving shields your wire and cable from signal interference. You can wrap this sleeving like tape around wire and cable while they’re installed, so it’s great for emergency patches.

Wrap your wire and cable to prevent electricity and heat from dissipating, even in high-voltage areas. Often used near generators and transformers, an acrylic resin in this sleeving insulates and protects your components.

Seal out dirt and dust better than standard slit sleeving—this sleeving secures shut with a closure strip. A slit along its entire length lets you install it around wire, cable, and hose that are already connected.

This sleeving reflects heat away from contents and withstands temperatures up to 300°F. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

The corrugated construction gives this sleeving impact and abrasion resistance similar to conduit, but with more flexibility.

The two halves of this sleeving nest into each other, fully enclosing contents. It has interlocking ridges that overlap to keep out dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

A hinge along the entire length makes this one-piece sleeving easy to open for installation. Interlocking ridges overlap along the opening to protect contents from dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

Extra-thick walls provide more protection against abrasion and tears than standard high-shrink-ratio tubing. This tubing shrinks down to 1/6th of its original ID, so it creates a tight seal over irregularly shaped objects.

The smallest heat-shrink tubing we offer, this tubing protects wire with a 0.017" and smaller diameter.

For better protection against abrasion, tears, and punctures, this tubing has thicker walls than standard tubing.

Made of woven polyolefin/polyester fabric, this tubing has excellent abrasion resistance so it can be dragged over rough surfaces without damage.

This tubing shrinks down to a quarter of its original ID, so it creates a tight seal over irregularly shaped objects. It withstands up to 500° F.

With thin walls, this tubing shrinks faster than other high-temperature tubing. It withstands up to 500° F.

Protect light bulbs, capacitors, and other electronics—this FEP tubing adds a tear- and cut-resistant layer that even contains shattered glass if the bulb breaks.

With excellent durability and chemical resistance, this tubing withstands demanding use.

Even with walls as thin as tracing paper, this PET plastic tubing withstands tears and nicks. Thanks to its thin walls, it shrinks down in seconds instead of minutes and at lower temperatures than PVDF and FEP plastic tubing.

Often used to bundle batteries, capacitors, and other electronics, this tubing tightly conforms to objects, similar to shrink wrap. It has excellent resistance to chemicals, oil, and acids.

Create a water-resistant seal—this tubing has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.

Also known as halogen-free tubing, this tubing produces minimal amounts of smoke and gas if exposed to an open flame, so it can be used in enclosed areas such as ships and tunnels.

This PTFE tubing withstands temperatures up to 450° F and has an inner lining that creates a water-resistant seal when heated.

Use this tubing where wire and cable may be exposed to chemicals, oil, and acids.

Seal the end of crimped connections, such as motor coils, to insulate and protect them from moisture and abrasion.

Also known as breakout boots, these splitters insulate and seal the point where wire splits off from cable, or where cables exit from conduit.

Protect wire and cable without disconnecting them from an assembly. For a water-resistant seal, this tubing has an adhesive lining that melts when heated to bond it to the underlying surface.

With a spiral-wound core, these end caps form a permanent seal on the end of your crimped wire or cable without heat or tools.

Maintain a supply of tubing in a variety of sizes that withstand abrasion, moisture, and chemicals.

Protect the cables on your TIG guns from weld spatter.