McMaster-Carr logo
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    9 Products

    Roller Chain and Links

    Image of Product. Front orientation. Roller Chain and Links. Roller Chain and Links, Chain.
    Image of Product. Front orientation. Roller Chain and Links. Roller Chain and Links, Connecting Links.

    Chain

    Connecting Links

    Image of Product. Front orientation. Roller Chain and Links. Roller Chain and Links, Adding Links.
    Image of Product. Front orientation. Roller Chain and Links. Roller Chain and Links, Adding-and-Connecting Links.

    Adding Links

    Adding-and-Connecting

    Links

    Image of Attribute. Front orientation. Contains Annotated.
    Pair this chain with sprockets to transmit power between rotating shafts. Like the chain on a bike, the side plates have a figure-eight shape that grips the sprockets without slipping.
    Lubrication is key to smooth operation and long chain life. Routinely apply oil by hand or install an oil dispenser for continuous lubrication.
    Steel—The go-to for roller chain, steel is strong and economical. While proper lubrication helps prevent rusting, it’s not as corrosion resistant as coated or stainless steel.
    Connecting Link—Use a single link to join both ends of your chain. Start by removing the spring clip or cotter pin from the link’s side plate. Then, slide the link pins into the mating rollers at each end of your chain and snap the clip back on. Also known as master links.
    Adding Link—Attach with a connecting link to extend the length of your chain. Each link adds a length equal to the chain’s pitch. Also known as roller links.
    Adding-and-Connecting Link—An all-in-one link for adding and connecting. It adds a half-pitch length at the roller end, allowing finer length adjustments than full-pitch links. The pin end connects to your chain—except for trade number 25, which requires a separate connecting link. Remove the side plate to install. Also known as half links and offset links.
    Chain
    Connecting Links
    Adding Links
    Adding-and-Connecting
    Links
    Roller
    Chain
    Trade
    No.
    Std.
    Pitch
    Roller
    Dia.
    Roller
    Wd.
    Working
    Load, lb.
    Per
    Ft.
    Each
    Each
    Each
    Triple Strand
     
    Steel
    40-3ANSI1/2"0.312"5/16"2,0206261K740000006261K752000006261K593000006261K753000000
     

    Floating Roller Chain Tensioners

    Image of ProductInUse. Front orientation. Contains MultipleImages. Chain and Belt Tensioners. Floating Roller Chain Tensioners.
    Mount these tensioners directly onto your chain drive. They have adjustable straps that take up slack and apply constant tension. Because they engage with the side plates instead of the rollers, they increase the life of your roller chain.
    UHMW Polyethylene—UHMW polyethylene tensioners are stronger and more durable than PTFE tensioners.
    Titanium—Titanium tensioners stand up to harsh and dirty environments. They're stronger and more durable than plastic tensioners. And with a low coefficient of friction, they work with chain that has little or no lubrication.
    Overall
    For Roller Chain
    Trade No.
    For Strand Type
    Ht.
    Wd.
    Dp.
    Housing Material
    Strap
    Material
    Max. Temp.,
    ° F
    Each
    For ANSI Chain
     
    UHMW Polyethylene
    76, 100, 60-2, 40-3Single, Double, Triple16"5"4 1/16"304 Stainless Steel
    		HDPE1805973K70000000
     
    Titanium
    76, 100, 60-2, 40-3Single, Double, Triple16"5"4 1/16"304 Stainless Steel
    		HDPE1805973K231000000
     

    Sprockets

    Image of Product. Front orientation. Drive Sprockets. Sprockets, For Triple Strand.

    For Triple Strand

    Sprocket teeth mesh with your roller chain to smoothly transmit power. These U.S.-made sprockets have machined teeth for a more precise fit than flame-cut or punched teeth, allowing them to glide in and out of the chain to reduce wear and extend chain life.
    Wear-Resistant Steel with Hardened Teeth—These sprockets have teeth that are hardened from the tip to the base so they withstand chain contact and wear evenly. That means fewer broken teeth and a longer lifespan than sprockets with unhardened or tip-hardened teeth. Steel is best for dry environments since moisture will cause it to rust.
    Plain Bore—Plain bore sprockets give you options—machine a custom bore, weld, or press-fit them in place. They're sized to the minimum shaft diameter listed and are machinable up to the maximum.
    For
    Roller Chain
    Trade
    No.
    Std.
    Pitch
    No. of
    Teeth
    OD
    Bore
    Type
    For Shaft
    Dia.
    Each
    For Triple Strand
     
    Wear-Resistant Steel with Hardened Teeth
    40-3ANSI1/2"112"Plain1/2" to 3/4"2510K250000000
    40-3ANSI1/2"152 5/8"Plain1/2" to 1 1/4"2510K29000000
    40-3ANSI1/2"203 7/16"Plain5/8" to 1 7/8"2510K35000000
     
    back to top