Made of stainless steel, these chucks are rust and corrosion resistant.

Use the included spanner wrench to tighten the chuck for up to three times the gripping torque of hand tightening.

Adapt standard impact wrenches for drilling applications. These chucks mount directly onto the square-drive spindle of an impact wrench.

A ball-bearing design provides increased gripping force to keep bits from slipping, which allows these chucks to take on high-torque drilling applications. Also known as super chucks.

A gripping ring in these chucks absorbs vibration and holds drill bits tighter than standard chucks during heavy hammer-drilling operations.

Convert a power screwdriver or impact driver into a versatile drill. Also known as adapt-a-drive, these chucks have a 1/4" hex shank that fits the hex drive in most power screwdrivers and impact drivers.

No more lost keys—also known as key leashes, use these holders to secure your chuck key to your drill's power cord.

These arbors with chuck allow drills with a Morse taper spindle to accept standard drill bits.

If your Morse taper arbor is too small or large for your machine spindle, insert it into one of these adapters. Also known as sleeves or shell sockets.

Insert your Morse taper arbor into one of these extensions to get additional reach.

These arbors are compatible with straight spindles, which are most often found on manual lathes and CNC machines.

Use with R8 taper spindles which are most often found on manual milling machines.

Use these collets to securely hold round-shank tool bits in the R8 spindle of a milling machine.

Install into an ER-16 collet chuck or holder to tightly grip round-shank tool bits in milling machines.

Install into an ER-11 collet chuck or holder to tightly grip round-shank tool bits in milling machines.

Insert into a 16C collet chuck or holder to tightly grip round workpieces. They provide a stronger hold on small workpieces than a standard lathe chuck.

Use these collets in milling machines that have an ER-25 collet chuck. With a round face and adjustable body, they compress to grip round-shank drill bits, end mills, reamers, and taps.

Also known as emergency collets, these collets have a machinable face for boring an opening to the exact size and shape you need.

When installed into a 3J collet chuck or holder, these collets securely grip workpieces.

Also known as step collets.

These collets tightly grip workpieces when installed into a 5C collet chuck or holder. They provide a stronger hold on small workpieces than a standard lathe chuck.

Install a 5C collet into one of these chucks to hold a workpiece for machining parallel or square edges and drilling crossholes.

Use to attach taps to Procunier auto-reversing tap holders.

No need to break down a collet set up when a workpiece doesn't fit a 5C collet. Install one of these lathe chuck adapters in your 5C collet chuck or holder and its three jaws will securely grasp the workpiece.

Made from hardened steel, these jaws have a long service life even when performing heavy machining such as roughing cuts.

When hand pressure is released, the wrench automatically pops out so you won't leave it in the chuck.

Secure jaws to a CNC lathe chuck with industry standard 1.5 mm × 60° serrations.

Consistently position workpieces in a three-jaw lathe chuck by installing a chuck stop. These stops enable short workpieces to extend beyond the chuck's jaws, providing additional clearance.

Sets include four vises with different opening sizes. A hollow body allows wires and rods to pass through.

Clamp and unclamp with one hand by sliding the knurled ring forward to close the collet.

Press the rotating end cap on the handle with your palm to apply constant pressure while turning the body of the vise with your fingertips.

Control clamping action with air. Use 5C collets to grip and release parts on milling machines and drill presses.

Grip and release parts using 5C collets. Use on milling machines, drill presses, or anywhere else you can mount this fixture.

Attach these chucks to your air hose so you can connect the hose to Schrader valves.

Attach to grinder and buffer shafts to hold buffing wheels with shanks.