Attach to the end of a screw or threaded stud to apply uniform pressure on uneven and angled surfaces. Also known as toggle and swivel-foot pads.

The contact area is covered in plastic to protect soft metal and polished surfaces. Attach these tips to the end of a screw or threaded stud to apply uniform pressure on uneven and angled surfaces. Also known as toggle and swivel-foot pads.

When loosened, you can spin the body of this clamp around its mounting point for better access to the workpiece.

Attach one of these nonmarring rubber or plastic tips to prevent a metal holding screw from damaging workpiece surfaces.

Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.

The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.

A nonreflective black oxide finish prevents glare that can interfere with machine vision systems.

Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.

Two sets of mounting holes allow mounting on the bottom or side.

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

The handle locks in a horizontal position for more clearance above the clamp.

These clamps have mounting holes on the bottom.

Hold a workpiece securely from the side with minimal contact, leaving more of the workpiece free for machining.

Machine these fixture clamps to match the contours of your workpiece for a stronger grip.

Set one of these clamps between two workpieces in a fixture and tighten the screw to push the clamp's sides out for a secure hold.

Tighten the spring-loaded socket head cap screw on these clamps to hold your workpiece from above.

Mount using the holes in the base.

Screw these clamps directly into a tapped hole in a fixture.

Turn the handle to tighten these multipurpose tools for strong clamping in nearly any application.

Plastic clamping surfaces prevent damage to material.

All components of these clamps are made of aluminum-bronze that is Factory Mutual approved. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Made entirely of fiberglass, these clamps won’t transmit electricity and are chemical resistant. They're often used around electrical equipment as well as in plating and anodizing applications.

With no handle or protruding screw, these clamps can fit into tight spaces.

The clamp body is extra-slim to fit into narrow openings.

The jaws move in unison to apply even pressure and prevent twisting.

Apply pressure to the side of a workpiece as well as the top and bottom.

Instead of a step block, support these clamps using a screw, leveling mount, or any other threaded object.

Use with T-slot nuts or bolts and a support to secure a workpiece, vise, or fixture to a machine table.

Designed to provide more clearance above the nut than standard clamps, these have an offset shape. Also known as gooseneck clamps.

Unlike other setup clamps that grip the horizontal surface of a workpiece, these clamps have a pivoting ball in the tip to get a firm hold on angled parts.

Get everything needed for basic workholding on a machine table.

Making minimal contact with the workpiece while holding securely, these clamps are good for small parts and can clamp into holes and notches.

Smaller than standard setup clamps, these clamps leave more usable space on a machine table when mounting a vise.

Also known as toe clamps, these grip the side of a workpiece to leave the top free for machining.

For the most demanding jobs, these clamps have almost five times the capacity of standard fast-action bar clamps.

Pull the handle to lock the jaw in place and prevent loosening caused by vibration.

All adjustments can be made from one end, allowing clamping in tight spaces.

Pull the lever to slide the clamping arm along the bar; release to lock in place.

Also known as J-clamps, these provide additional clearance to reach around obstructions and clamp workpieces in recessed areas.

Each arm slides freely for quick, one-handed positioning. They lock when the screws are tightened onto a workpiece.

Clamp much farther in from the edge of the workpiece than with standard bar clamps.

The large, flat jaws remain parallel when clamping to apply even pressure without denting or marring the workpiece. Pull the handle to lock or release the clamping arm.

The matching jaws are ground flat for a firm grip and even pressure when clamping smooth surfaces.

Mount through the counterbored hole with a socket head cap screw to support and position workpieces and fixtures from the bottom or side.

For maximum contact with angled and uneven surfaces, the tip swivels in all directions. The tip is narrow so it will fit through threaded holes.

Arms provide a flat surface to push your fingers against.

Made from 18-8 stainless steel, these thumb screws are chemical resistant. Also known as dog- and pilot-point thumb screws, insert the point into a drilled hole or slot to hold items in place.

These steel thumb screws have a black-oxide finish to resist corrosion in dry environments.

A knurled head allows for slip-resistant controlled adjustment.

A large head allows you to grip these screws with your entire hand for greater torque while tightening than standard knurled plastic-head thumb screws.

Tighten these thumb screws by hand or with a hex key for more torque.

These metric thumb screws have a thin, knurled head for use in low-clearance applications. They have a black-oxide finish to resist corrosion in dry environments.

Made from 18-8 stainless steel, these thumb screws are chemical resistant. They have a thin, knurled head for use in low-clearance applications.

Brass thumb screws are corrosion resistant in wet environments and electrically conductive.

A raised head makes these thumb screws easy to grip. They have a black-oxide finish to resist corrosion in dry environments.

Made from 18-8 stainless steel, these thumb screws are chemical resistant. They have a raised head that makes them easy to grip.

Stainless steel thumb screws have excellent corrosion resistance in most environments.

Aluminum thumb screws are lightweight and resist corrosion in wet environments.

These steel thumb screws have a black-oxide finish to resist corrosion in dry environments.

Use these slim thumb screws in tight spaces.

Wings provide more leverage than spade-head thumb screws for greater torque while tightening. A zinc plating provides corrosion resistance in wet environments.

A raised head makes these thumb screws easy to grip. Made from nylon, they're chemical resistant, nonconductive, and lightweight.

These nylon thumb screws are chemical resistant, nonconductive, and lightweight.

A flange provides a bearing surface to hold parts under the head.

Fasten material by hand, so tools don’t scratch or contaminate parts you frequently adjust in food-processing or pharmaceutical plants.

These steel thumb screws have a black-oxide finish to resist corrosion in dry environments.

A wide tip provides more gripping power than standard swivel-tip set screws. To use, remove the tip, thread the screw through the hole, and attach the tip on the other side.

These set screws have a low-profile flat-faced ball tip for use in low-clearance applications.