Hold lightweight objects, secure covers, and seal bags.

These V-shaped liners hold large round material.

Use these components in coordinate measuring machine (CMM) applications to raise a workpiece and reliably position it on a fixture plate with ¼"-20 holes.

Slide these clamps over your hose and heat-shrink them with a heavy duty heat gun. This process lets them conform to any shape hose.

Connect quick-clamp sanitary tube fittings—also known as aseptic fittings—for a fast and easy way to access your line.

Connect two pipes that are up to 100 feet apart—cut the connector to the length you need and attach a clamp to each end.

Snap these clamps around leaking pipe with only your hands. No tools required.

Also known as Victaulic pipe, this pipe has grooved ends that connect to fittings and flanges with a clamp, so you can access your line for routine maintenance. It is CPVC, which has excellent chemical resistance to withstand a variety of salt solutions, acids, and other harsh substances.

The grooved ends on these flanges connect to pipe with a clamp, so you can access your chemical process line for routine maintenance. Flanges have excellent chemical resistance to withstand a variety of salt solutions, acids, and other harsh substances. They are also known as Victaulic flanges.

Connect these fittings to Schedule 40 plastic pipe—they are the industry standard for residential and commercial low-pressure plumbing and water supply applications. They are plastic for good corrosion resistance.

These Schedule 40 fittings are the industry standard for gravity-flow drain, waste, and vent (DWV) applications.

Made of nylon, these fittings are lighter in weight than metal garden hose fittings. Attach them to garden hose for a variety of water supply applications.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

Slide these clamps into strut channel and snap closed for quick installation with no tools required. They are noncorrosive, nonconductive nylon.

Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.

Clip these hangers onto the side of threaded rod. Unlike other threaded-rod-mount hangers, you can use more than one hanger on the same rod to organize multiple lines of pipe, tubing, and conduit.

These plastic rings won't conduct electricity. Also known as distribution rings, they have a large opening for routing multiple cables. A smooth surface prevents damage to wire and cable.

Attach these supports onto metal stud knockouts to route cable, conduit, and tubing through metal studs.

These mounts create space between a bundle and surface.

Route and organize wire, cable, and hose along your DIN rail. Unlike zip ties, these cable ties can be temporarily undone to add or remove material.

Attach these cable ties directly to a surface—no separate mount needed.

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.

Made of chemical-resistant nylon, these collars are suitable for washdown applications.

Use these handles for applications involving frequent positioning, tightening, and holding adjustments near food processing lines without the risk of contaminating the food. These handles are also known as clamping handles.

Identify equipment controls and components at a glance by their color. Mount these knobs into a threaded hole. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Bonded to the stud is an acrylic adhesive that adds friction to resist loosening from vibration. Use these knobs to position, tighten, and hold fixtures, equipment, and machinery. They mount into a threaded hole.

Knobs have left-hand threads; they're used in applications where counterclockwise motion can loosen common right-hand threads. Mount them into a threaded hole to position, tighten, and hold fixtures, equipment, and machinery.

Quick to install, position, and remove, these knobs have an angled hole that allows you to tilt the knob to slide it over threads, then straighten it to grip the threads and secure the knob. They provide a firm grip to position, tighten, and hold fixtures, equipment, and machinery.

A rubber coating provides a comfortable grip to position, tighten, and hold fixtures, equipment, and machinery. Long shafts can thread through these knobs for mounting versatility.

Install these knobs on a threaded stud. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

A rubber coating provides a comfortable grip to position, tighten, and hold fixtures, equipment, and machinery. Install these knobs on a threaded stud.

Tap custom threads or secure with a set screw to provide a firm grip to position, tighten, and hold fixtures, equipment, and machinery.

Create custom threads or secure with a set screw to provide a firm grip to position, tighten, and hold fixtures, equipment, and machinery. Long shafts can pass through these knobs for mounting versatility.

Often used on pallet and lift trucks, these knobs attach to steering wheels for one-hand operation.

Lock Ethernet cords in place to prevent unauthorized removal from ports.

Use these accessories to mount carriers to your machinery without creating an obstruction.

The hinged snap-on crossbars open for access at any point along the carrier's length so you can lay in the cable and hose, rather than threading it through.

By completely surrounding the cable and hose, these carriers protect them from dirt, chips, and debris.

Slide these clips on DIN rails—often used in equipment cabinet racks—to route and organize cables. Since these clips don’t require adhesive or screws, you can move them anywhere along the rail.

Adjust the latching distance for a tight fit over gasketing and to compensate for misalignment.

Route wires, cables, and tubing along T‐slotted rails.

No need for fasteners—friction holds this framing together. Use press-fit framing and fittings to assemble carts, enclosures, and partitions.

Racks have multiple holders to organize items.

Adhesive strips let you remove and reuse these holders without damaging the wall.

Brackets are sized to mount sensors and reflectors to a conveyor frame.

These brackets mount to the frame of a conveyor to hold guide clamps.

Spacers increase the distance between a bracket and the conveyor frame.

Separate products into distinct lanes with guides and nose plows.

A raised head makes these thumb screws easy to grip. Made from nylon, they're chemical resistant, nonconductive, and lightweight.

These nylon thumb screws are chemical resistant, nonconductive, and lightweight.