These latches reach around outside corners to draw two surfaces together—use them to secure cases, toolboxes, and other containers.

A safety catch prevents accidental opening.

A plastic-coated handle and hook prevents the release of particles from metal-to-metal contact, which makes these latches good for clean room applications.

To prevent accidental opening, these latches have a safety catch.

Mount these latches on a corner to draw perpendicular surfaces together.

No need for a strike plate, these latches hook into a lip or notch.

A safety catch prevents accidental opening.

These latches have a safety catch to prevent accidental opening.

To prevent accidental opening, these latches have a safety catch.

Lift and turn the handle 180° to open and close these latches.

Draw lightweight surfaces together with these latches.

These latches snap in place to eliminate rattling and hold access doors, screens, windows, and panels.

Add a padlock to secure these latches, which reach around corners to pull two surfaces together.

Mount these latches on a corner to draw perpendicular surfaces together. They have a safety catch to prevent accidental opening.

An integrated slide bolt extends into the strike plate to resist pull and vibration from side-to-side, front-to-back, and up-and-down forces.

Lift and turn the handle 180° to open and close these latches. Add a padlock to secure.

Secure cases, toolboxes, and other containers—these locks reach around outside corners to draw two surfaces together.

Open several draw locks with the same key.

A catch grabs and holds the strike plate to keep doors shut.

Their spring-loaded design withstands vibration, rattling, and shaking better than other push-to-close grab latches for a more secure hold.

Each latch has top and bottom spring-loaded balls that can grab the strike plate from different directions.

These latches are adjustable; push the ball in and rotate it to adjust force as well as compensate for misalignment.

Magnetic force holds doors closed.

Made to NSF/ANSI standards, these latches have a completely sealed magnet to eliminate crevices that can trap food particles.

There's no need for a mating strike plate for these latches—their spring-loaded arm snaps to engage when closing the door.

These latches are spring-loaded to overcome resistance caused by gaskets and air pressure to close doors tightly.

Their spring-loaded design withstands vibration, rattling, and shaking better than other face-mount push-to-close latches for a more secure hold.

For use on spray booths and drying ovens, these latches automatically open when the internal pressure of the enclosure reaches a set level.

Attach these padlockable latches vertically to the side edge of doors on refrigerators, ovens, and industrial enclosures with the strike plate mounted behind it on the frame.

An emergency release handle offers a means of escape if a door closes with someone inside an enclosure.

To open, push in the knob and pull the tab.

An emergency release handle offers a means of escape if the door closes with someone inside an enclosure. Mount these locks horizontally to the face of doors on refrigerators and industrial enclosures with the strike plate mounted on the frame.

Turn the padlock eye to fasten these hasps without a padlock.

Install these hasps over a cam lock and secure them with a padlock to increase security on cabinets and chests.

Designed for use with cut-resistant padlocks, these hasps have a padlock shackle protector on the strike plate for added cut and pry resistance.

Mount these padlockable eyes to the front of a door and door frame.

Choose these hasps if you need hasps that each open with a different key.

These locks are IP65 and NEMA 4 rated for protection against dust, dirt, and washdowns.

Use these locks in a 3/4" dia. through hole, which is the most common through-hole size.

Meet U.S. postal service guidelines for mailbox locks.

Use these locks in a 3/4" dia. through hole, which is the most common through-hole size.

Designed for use in 1/2" dia. through holes.

Use these locks in a 3/4" dia. through hole, which is the most common through-hole size.

Made of plastic, these locks are suitable for damp and humid environments.

These highly pick-resistant locks have specially designed half-moon keys that cannot be duplicated.

These sets come with four cam locks that are divided into two groups of two. Each group of cam locks opens with a specific key number. All open with the same master key.

These highly pick-resistant locks have specially designed half-moon keys that cannot be duplicated.

These locks have a spring-wire cam that slips under a receiving catch on a cabinet body to create tension and hold cabinet doors and drawers closed.

For protection against dust, dirt, and washdowns, these locks are IP65 rated.

Use these locks in a 3/4" dia. through hole, which is the most common through-hole size.

Designed for food-processing and hygienic applications, these corrosion-resistant cam locks are made of FDA listed materials.

Also known as compression cam locks, turn the head a quarter-turn to latch, then another quarter-turn to draw the cam firmly against the door or drawer surface.

Also known as compression cam locks, turn the handle a quarter-turn to latch, then another quarter-turn to draw the cam firmly against the door or drawer surface.

The mounting screws on these locks are concealed to prevent tampering.

In addition to an IP65 rating for washdown environments, these locks have a squeeze-release handle to prevent accidental opening when unlocked.

The mounting screws on these locks are concealed to prevent tampering.